Automatic Technology GDO-6v4 EasyRoller Скачать руководство пользователя | Manualshive

Страница: 34 / 36

background image

34

GDO-6v4 EasyRoller

®

Owner Installation Instructions

Please refer to the risk assessment table below and ensure all the necessary controls are in place.

Installation Risk Assessment

Hazard

Control

Muscular strain from incorrect
lifting of opener

Practice correct lifting techniques (carton weighs 9 kg)

•

Muscular strain from incorrect
lifting of door

Practice correct lifting techniques when required to lift the door as
per installation instructions

•

Entanglement in operating Opener

Never plug in and operate prior to installation

•

Uncontrolled spring tension
release

Follow the installation instructions
Ensure the U-bolt on the opposite end to the motor is tight
Do not conduct any door repairs or maintenance (contact
professional for all door servicing)

•
•
•

Fall from ladder

Ensure ladder is the correct type for job
Ensure ladder is on ﬂ at ground
Ensure user has 3 points of contact while on ladder

•
•
•

Crush injury from unsecured door

Place a 2 metre exclusion zone around area under the door while it is
unsecured
Do not move under door while on door support (or ladder)
Follow the installation instructions
Fit door support (or ladder) snugly under door before removing U-
bolt and bracket
Ensure door support (or ladder) is on ﬂ at ground

•

•
•
•

•

Testing and Operation Risk Assessment

Hazard

Control

Entrapment under operating door

Keep children clear of operating door
Ensure the garage door is in good working order
Correctly set the Safety Obstruction Force
Install Photo Electric Beams (recommended)
Do not operate door when persons are near the door

•
•
•
•
•

Entanglement in moving door

Fit locking bar covers
Keep hands and loose clothing clear of door and guides at all times

•
•

Entanglement in operating Opener

Never plug in and operate prior to installation

•

Electrocution

Place opener in protected area so that it does not get wet
Do not spray with water
Do not open the protective covers
Do not operate opener if cable is damaged

•
•
•
•

Important Safety Checks

«
...
32
33
34
35
36
»

Содержание GDO-6v4 EasyRoller





































Отзывы:

Нет отзывов

Похожие инструкции для GDO-6v4 EasyRoller

Бренд: FAAC Страницы: 6

Бренд: quiko Страницы: 32

Бренд: Gainwise Страницы: 17

Бренд: cedamatic Страницы: 20

Бренд: Eagle Страницы: 47

AccessMaster M100

Бренд: Chamberlain Страницы: 36

WING 302 Series

Бренд: Dea Страницы: 32

Бренд: Dea Страницы: 44

Бренд: quiko Страницы: 2

Бренд: Beninca Страницы: 12

Бренд: Wayne-Dalton Страницы: 20

Calypso 400-120V

Бренд: V2 Страницы: 11

Бренд: Overhead door Страницы: 2

Бренд: D-force Страницы: 12

Бренд: PowerTech Страницы: 29

Бренд: MicroTeq Страницы: 22

Бренд: Cardin Страницы: 16

Бренд: Cardin Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды