manualshive.com logo in svg

Automatic Technology GDO-6v4 EasyRoller, Руководство по установке

Поделиться
Скачать
Automatic Technology GDO-6v4 EasyRoller Скачать руководство пользователя страница 7

 

Owner Installation Instructions 

GDO-6v4 EasyRoller

®

7

Vacation mode

A handheld transmitter can be programmed to lock and unlock all other transmitters that have been 

programmed into the openers’ memory. The vacation mode can be used when the door is left 

idle for long periods of time.

Auto courtesy light

The courtesy light comes on automatically for three minutes whenever the door is 

activated. The light can also be operated independently of the door by coding a 

dedicated button on a transmitter.

Pet/Pedestrian mode

The transmitter can be programmed to open the door to an adjustable partial 

height so that the family pet can enter and exit the garage at any time. You may 

also wish to open the door to a height suitable for pedestrian access.

Auto-Close mode

The opener can be programmed to automatically close after an open cycle. The 
Auto-Close time is adjustable. It is compulsory to install a Safety Beam if this 

mode is selected, otherwise the door may cause personal injury or damage to 

property.

Safety Beam (optional)

The opener has an input to connect a Safety Beam for extra safety and use of the 

Auto-Close mode. Easy Beam PE 3 kit or Wireless Safety Beam kit can be used with 

this opener.

Safety Beam Failure Emergency Close

When a safety beam prevents movement due to any reason other than a ‘real’ 

obstruction, the user can secure their property by pressing and holding a button on the 

remote control or OSC on the console.

Manual operation

The opener is equipped with a unique manual disengaging device. If the power to the opener is 

disrupted, the door can be put into manual mode by pulling down on the string handle on an angle towards 

the door. This allows for manual operation of the door. To re-engage the opener, pull the string handle away 
from the door.

Easy Access Transmitter

Inside the manual release handle is a transmitter designed to be in easy reach so that the garage door can 
be operated without having to stretch to reach the operate button on the control panel.

Service Indicator

The opener has a built in counter with a default setting of 3000 cycles. When the counter expires the opener 
will beep and fl ash to indicate a service is required.

Содержание GDO-6v4 EasyRoller





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды