manualshive.com logo in svg

Automatic Technology GDO-6v4 EasyRoller, Руководство по установке

Поделиться
Скачать
Automatic Technology GDO-6v4 EasyRoller Скачать руководство пользователя страница 6

6

GDO-6v4 EasyRoller

®

 

Owner Installation Instructions

Operation

To open or close the door simply press a button on a TrioCode™ handheld 
transmitter, a wall mounted transmitter, or optional wall switch for two seconds. 
During open and close cycles the door can be stopped by pressing the button 
again. The next actuation will move the door in the opposite direction.

TrioCode™ Code Hopping Technology

Every time a TrioCode™ transmitter is used, a new security code is randomly 
generated from over 4.29 billion possibilities. This greatly enhances the security of 
the system and makes “code grabbing” a thing of the past.

These transmitters also overcome interference issues by simultaneously sending a 
signal over three slightly different frequencies. Even if two of the three signals are 
jammed, the system will still work.

ALPS (Automatic Limits Positioning System)

ALPS does away with manual adjustment of the door’s limits position using mechanical 
parts, such as cams and microswitches. During installation the handheld transmitter can be 
programmed to set the door limits positions.

ISS (intelligent safety obstruction system)

While the door is performing a close cycle, should it hit an obstacle or be restricted in some 
manner, it will automatically reverse. The amount of force the door should encounter before reversing 
is automatically adjusted by the doors control system during the initial installation of the automatic door 
opener. The door will also stop if restricted whilst opening. The Safety Obstruction Force should be checked 
monthly.

SmartSolar™ and Battery Backup Compatibility (optional)

The opener can be fi tted with a SmartSolar™ or Battery Backup kit for operation in the event of a power outage, 
or where mains power access is not available.

NOTE: 

If the door is the only entrance to the garage, and a battery backup kit is not fi tted, a keyed cable 

release should be fi tted externally to the garage.

Features

Thank you for purchasing the Automatic Technology 
EasyRoller® Automatic Garage Door Opener. 
Designed by our renowned engineers to suit Vertical 
Operating Continuous Curtain Roll up doors, the 
EasyRoller® will provide years of smart, simple 
& secure convenience to your home. 

Содержание GDO-6v4 EasyRoller





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды