Automatic Technology GDO-6v4 EasyRoller Скачать руководство пользователя | Manualshive

Страница: 11 / 36

background image

Owner Installation Instructions

GDO-6v4 EasyRoller

®

11

Installation

Pre-Installation Requirements

IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION

Warning: Incorrect installation can lead to severe injury.

Follow ALL installation instructions.

01

ﬁ g

02

ﬁ g

Door Operation

The door must be in good operating condition. The
maximum effort to move the door up or down, from
stationary, should not exceed 150 Newtons (15kg force) at
the bottom rail. The recommended force is 70N (7kg) for
manual operation.

Lift the door to about halfway. When released, the door
should stay in place supported entirely by its springs. Raise
and lower the door to check for binding or sticking.

The door may need to be serviced to meet these
requirements – refer to the door manufacturer’s servicing
instructions or contact an authorised dealer.

Unsuitable Door Types

The ﬁ tting of an opener to doors with removable mullions is
not recommended.

IMPORTANT NOTE -

The opener should not be

installed on any door incorporating a wicket door.

Position

The opener can be installed on either the right- or left hand
side of the door (when viewed from inside the garage). The
opener is factory set for right hand side installation.

This opener must be installed in a dry position that is
protected from the weather. Moisture or corrosion damage
is not covered by the Warranty.

Power Supply

Properly earthed 3 pin single-phase power is required.

WARNING!

A portable power generator is

not recommended. The opener may appear to
malfunction due to spikes, surges and ﬂ uctuations in
the generated voltage.

Sideroom

The minimum sideroom required from the edge of the door
curtain is 40mm to the inside of the door bracket, and 85mm
to the wall

(Fig. 01)

. If a Battery Backup Kit is to be ﬁ tted, at

least 135mm to the bracket is required

(Fig. 01a)

.

The recommended sideroom from the edge of the door
curtain is 95mm to the inside of the door bracket, and
135mm to the wall

(Fig. 02).

NOTE:

Door Axle Diameter must not exceed 35mm.

135

01a

ﬁ g

«
...
9
10
11
12
13
...
»

Содержание GDO-6v4 EasyRoller





































Отзывы:

Нет отзывов

Похожие инструкции для GDO-6v4 EasyRoller

Бренд: Wayne-Dalton Страницы: 18

Бренд: Wayne-Dalton Страницы: 22

Бренд: 4Ddoors Страницы: 14

Бренд: International Door Closers Страницы: 2

Бренд: DTS Страницы: 19

Бренд: West Bend Страницы: 20

Бренд: GFA Страницы: 20

Бренд: Roger Technology Страницы: 16

Бренд: V2 Страницы: 29

Бренд: Label Страницы: 64

Бренд: Roger Technology Страницы: 72

Бренд: Roger Technology Страницы: 16

Бренд: CAB Страницы: 15

Бренд: Beninca Страницы: 20

Бренд: Langer & Laumann Страницы: 84

Бренд: CAME Страницы: 2

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды