manualshive.com logo in svg

Automatic Technology GDO-6v4 EasyRoller, Руководство по установке

Поделиться
Скачать
Automatic Technology GDO-6v4 EasyRoller Скачать руководство пользователя страница 32

32

GDO-6v4 EasyRoller

®

 

Owner Installation Instructions

Maintenance

Whilst your opener does not require any periodic 
maintenance, the door that it is fi tted to, does. 
Your garage door is a large, heavy, moving object 
and should be tested regularly to ensure it is in 
good condition. A poorly maintained door could 
cause fatal or serious injuries or serious damage to 
property.

To ensure a long and trouble free life for your opener 
the following is recommended:

Monthly

Disengage the opener and manually operate 
the door: The door must be smooth to operate 
by hand. An operating force on the bottom rail 
should not exceed 150N (15kg) force.
Each month check that the opener reverses 
when the door contacts a 40mm high object 
placed on the fl oor (AS3350). 

NOTE:

 If the door does not operate smoothly, call 

your door professional.

•

•

•

Maintenance counter

GDO-6v4 EasyRoller® has a built in maintenance 
counter. From factory this is loaded with 3000 cycles. 
When this counter expires, the service yellow LED will 
light up. At the start of each  door movement the beeper 
will sound three times. After opening or closing the door 
the courtesy light will fl ash and beeper sound fi ve times.

At this time Automatic Technology recommends you 
contact your door professional to perform an annual door 
service. 

When maintenance counter is active it can be reloaded 
with 3000 cycles by press and holding the SET button on 
the console.

CAUTION: 

Frequently examine door, particularly 

cables, springs and mountings for signs of wear, 
damage or imbalance. Do not use if repair 
or adjustment is needed since a fault in the 
installation or an incorrectly balanced door may 
cause injury. (AS3350)

Adjustments should only be carried out by 
experienced persons, as this function can 
be dangerous if not performed under strict safety 
procedures.

WARNING! 

Failure to maintain your garage 

door may void the warranty on your garage door 
opener.

Maintenance

Date

Service by

Signature

Invoice No.

Amount

Service Record

Record any maintenance in the following table to assist in any warranty service.

Содержание GDO-6v4 EasyRoller





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды