background image

This Installation document is available at no charge from:
- Your local Wayne Dalton Sales Center, or
- Online at 

www.Wayne-Dalton.com

, or

- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 

67, Mt. Hope, OH., 44660

©Copyright 2017

REV12_04/21/2017

Part Number

T a b l e   O f   C o n t e n t s

345571

PLEASE DO NOT RETURN THIS PRODUCT 

TO THE STORE

If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the 
prompts to contact a customer service 
representative. They will be happy to handle 
any questions that you may have.

Pre-Installation 2

Important Safety Instructions 

2

Removing an Existing Door and Preparing the Opening 

2

Package Contents 

3

Door Section Identification 

4

Tools Required 

4

Breakdown Of Parts 

6

Installation 7
Counterbalance Installation Instructions 

10

Optional Installation 

17

Door Arm Hookup 

17

Inside Lock 

17

Pull Down Rope 

17

Maintenance 18

Cleaning Your Garage Door 

18

Maintaining The Finish On Your Garage Door 

18

Operation And Maintenance 

18

Warranty 19

Wayne Dalton, a division of Overhead Door Corporation

Model 9800

T

o r s i o n

i

nsTallaTion

 i

nsTrucTions

 a

nd

 o

wner

s

 

M

anual

r

esidenTial

 

and

 l

ighT

 c

oMMercial

 

F

ronT

 M

ounT

 l

ow

 h

eadrooM

 

o

uTside

 h

ookup

DEFINITION OF LIGHT COMMERCIAL:

1. Door Heights less than or equal to 8’0” (< = 8’0”) are considered 
Residential Applications.
2. Door Heights greater than 8’0” (> 8’0”) are considered Light 
Commercial Applications.

To avoid possible injury, read and fully understand the enclosed 
instructions carefully before installing and operating the garage door. Pay 
close attention to all warnings and notes. After installation is complete, 
fasten this manual near garage door for easy reference.

IMPORTANT NOTICES!

Содержание 9800





















Отзывы: