background image

Weather seal

s

Nail

Weather 

seal

Jamb

Weather seal 

installed

Jamb

Header

Jamb

Nail

NOTE:

 Door not shown for clarity.

Balancing Door

 

22

 

Remove locking pliers. Lift door and check its balance. Adjustments to the required number 

of spring turns stated may be necessary. If door rises off floor more than 2 ft. under spring 

tension alone, reduce spring tension. If the door is hard to rise or drifts down on its own, add 

spring tension. A poorly balanced door can cause garage door operator problems.
To adjust spring tension, fully close door. Apply locking pliers to track above third track roller. 

Place locking pliers on torsion shaft, as shown in D5. Insert a winding rod into the winding 

cone. Push downward on the winding rod slightly while carefully loosening the set screws in 

the winding cone.

IMPORTANT: 

BE PREPARED TO SUPPORT THE FULL FORCE OF THE TORSION SPRING ONCE 

THE SET SCREWS ARE LOOSE.
Carefully adjust spring tension 1/4 turn. Retighten both set screws to 14-15 ft. lbs. of torque 

in the winding cone and repeat for the other side. Recheck door balance and re-adjust spring 

tension if needed.

IMPORTANT: 

DO NOT ADJUST MORE THAN 1 TURN FROM THE RECOMMENDED NUMBER 

OF TURNS.
If the door still does not operate easily, lower the door into the closed position, unwind 

spring(s) completely, and recheck the following items:
1.) Is the door level?
2.) Are the torsion shaft and flag angles level and plumb?
3.) Does the distance between the flag angles equal door width plus 3-3/8” to 3-1/2”?
4.) Do the counterbalance lift cables have equal tension? Adjust if necessary.
5.) Rewind the spring(s).
6.) Make sure door is not rubbing on jambs.

IMPORTANT: 

IF DOOR STILL DOES NOT BALANCE PROPERLY, THEN CONTACT A TRAINED 

DOOR SYSTEM TECHNICIAN.

16

Содержание 9800





















Отзывы: