Audison bit Tune Скачать руководство пользователя страница 46

Страница: 46 / 100

USER’S MANUAL / bit Tune /

Clicking on the

Settings

button opens a drop down menu as shown on the right:

1. MIC CALIBRATION

This function starts a wizard for calibrating the

HSM

microphone. The procedure must be performed when

using the instrument for the first time and periodically according to use

(see sect. 7.1)

2. CONNECT TO

This feature allows to connect and synchronize the PC

Software to the bit Tune or to the Audison bit processor,

connecting it via the USB OUT port of the bit Tune.

When the Audison processor connection is active

(see sect. 6.2.6),

it will not be possible to interact with the PC

software of the Audison processor.

Select

Connect to -> bit Tune

to connect the PC Software to the bit Tune.

Select

Connect to -> Processor

to connect the PC Software to an Audison bit processor.

3. DISCONNECT TO

This feature allows you to disconnect from the bit

Tune PC Software a previously interfaced Audison

processor or the bit Tune itself. When the processor is

DISCONNECTED from the Tune bit PC Software, but is

still connected via the USB cable, you can use the

processor’s PC software in conjunction with the software

of the bit Tune.

Select

Disconnect -> bit Tune

to disconnect the bit Tune from the PC Software.

Select

Disconnect -> Processor

to disconnect the Audison bit processor from the PC Software.

6.2.5

“SETTINGS” MAIN MENU

Содержание bit Tune





































































































Результаты поиска

Содержание bit Tune

Отзывы:

Бренды по названию

Популярные бренды

Audison bit Tune, Руководство пользователя

Результаты поиска

Содержание bit Tune

Отзывы:

Бренды по названию

Популярные бренды