manualshive.com logo in svg

Audison bit Tune, Руководство пользователя

Поделиться
Скачать
Audison bit Tune Скачать руководство пользователя страница 10

USER’S MANUAL / bit Tune /

10

1. POWER:

 The blue LED indicates that the bit Tune is powered on.

2.  EMS - LINE NOISE - PC ANALYZER:

 Switch for selecting measurement settings.

3. PROBE:

 The yellow LED indicates that the EMS socket is activated 

(see sect. 8.4)

.

4.  PRE IN PC ANALYZER LED:

 Green LED, indicates the 

PRE IN

 input selection for measurements performed  

 

through the bit Tune PC software 

(see sect. 7)

.

5.  PRE IN LINE NOISE LED:

 Yellow LED, indicates the 

PRE IN

 input selection for the measurement of noise  

 

through the internal speaker monitor of the bit Tune.

6.  SIGNAL INPUT SELECT:

 Switch for the selection of 

PRE IN, BNC, SPK IN

 measurement inputs of the bit Tune.

7.  BNC PC ANALYZER LED:

 Green LED, indicates the 

PRE IN

 input selection for measurements performed  

 

through the bit Tune PC software.

8.  SPK IN PC ANALYZER LED:

 Green LED, indicates the 

SPK IN

 input selection for measurements performed  

 

through the bit Tune PC software.

9.  SPK IN LINE NOISE LED:

 Yellow LED, indicates the 

SPK IN

 input selection for measurements performed  

 

through the bit Tune PC software

10. VOLUME:

 Volume control of the internal speaker monitor of the bit Tune.

11.  Ch LEFT Ch RIGHT:

 Switch for selecting the 

SPK IN

 Left or Right input in line noise analyzer mode. 

12-13-14. LOAD SIMULATOR SPEAKER IN: 

Through the 

SPEAKER IN LOAD SIMULATOR-SELECTOR

 button  

 

(see sect. 3.2.6)

 it is possible to verify, through the switching of the LEDs, if the source requires a load for operating  

 properly 

(see sect. 8.1)

.

 

  NO LOAD:

 Green LED. No load.

 

  47 OHM:

 Yellow LED. Requires a 47 Ohm - 5 W resistance.

 

  SPK IN:

 Orange LED. Requires an inductive load.

15.  SPEAKER MONITOR

: Internal speaker for monitoring audio signal inputs to the bit Tune.

3.3 

CONTROL PANEL

EMS

PC ANALYZER

LINE NOISE

POWER

SIGNAL INPUT

SELECT

RIGHT

VOLUME

MONITOR

47 OHM

SPK SYM

NO LOAD

LEFT

PRE IN

BNC

SPK IN

PROBE

MIN •

• MAX

LOAD SIMULATOR

SPEAKER IN

1

2

4

5

6

3

7

8

9

10

15

12

11

13

14

3

Содержание bit Tune





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды