manualshive.com logo in svg

Audison bit Tune, Руководство пользователя

Поделиться
Скачать
Audison bit Tune Скачать руководство пользователя страница 5

USER’S MANUAL / bit Tune /

5

Before using the bit Tune, please refer to all instructions contained in the manual. We recommend to closely 

follow the instructions. Failure to comply with these instructions could result in unintentional injuries or damage to 

equipment or devices connected to it.

WARNING:

 do not connect the bit Tune probes to the mains voltage. The product is not designed for measuring the

 

 

mains voltage (110/220 VAC). Such connection, in addition to damaging the device, it could be very 

 

 

dangerous to the user!

1. 

In order to use the measurement tools of the bit Tune, you must install the software on a personal computer 

running Windows XP, Windows Vista or Windows 7, with a 1.5 GHz processor or higher, 1 GB of RAM and a 

graphics card with minimum resolution of 1024 x 600 pixels.

Note:

 -  The bit Tune PC software might show malfunctioning with some PCs manufactured before 2006 even 

  

  with processors running at higher speed than the minimum required. It is recommended to check using 

  

  “Windows Update” and make sure that the available updates are installed in the PC.

  

-  Before performing the measurements, check that the Antivirus is not scanning the PC. If you experience 

  

  any problems, it is advisable to disable the Antivirus, even if it is not scanning the PC, and close all the other 

  

  running  programs.

2.

  Please use only the specific power adapters provided in the package.

3.

  For use in the car please check that the vehicle’s electrical system has a supply voltage of 12 VDC with negative 

to ground. If you are using the network adapter, select the power supply connector suitable for the country of 

use (provided in the package).

4.

  Do not perform any measurement in the engine compartment and in locations exposed to water, excessive 

moisture, dust and dirt.

5.

  Take measurements in places where the temperature does not go below 0 °C (32 °F) and does not exceed 55 °C

 

(131 °F).

6.

  Make sure that the positioning of the device does not interfere with the proper functioning of the car’s electrical or

 

mechanical devices.

7.

  Make sure you do not short the power cord during the measurement.

8.

  In order to facilitate the measurement, route the cables the best possible way, using cables supplied with the 

  

product and referring to instructions provided in the USER’S MANUAL.

1.1 

PRECAUTIONARY NOTES

1

Содержание bit Tune





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды