AuCom EMX3-0053B Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 24

AuCom EMX3-0053B Скачать руководство пользователя страница 1

USER MANUAL

MODBUS TCP INTERFACE

RIGHT FROM

THE START

Modbus TCP Interface | Rev D 3/2019

Contents

Warnings .............................................................................................. 2

Important User Information ................................................................ 2

Installation ........................................................................................... 3

Device Configuration ........................................................................... 6

PLC Configuration ............................................................................... 8

Feedback LEDs .................................................................................... 8

Operation ............................................................................................. 9

Modbus Registers .............................................................................. 10

Network Design ................................................................................. 21

Specifications .................................................................................... 23

Product Compatibility

The Modbus TCP Interface is compatible with the following AuCom soft starters:

•

CSX – 24 VAC/VDC and 110/240 VAC control voltage.
The Modbus TCP Interface is not suitable for use with CSX starters using 380/440
VAC control voltage.

•

EMX3 – all models.

•

MV – all models.

Disclaimer

The examples and diagrams in this manual are included solely for illustrative
purposes. The information contained in this manual is subject to change at any time
and without prior notice. In no event will responsibility or liability be accepted for
direct, indirect or consequential damages resulting from the use or application of this
equipment.

© 2019 AuCom Electronics Ltd. All Rights Reserved.

1
2
3
...
»

Содержание EMX3-0053B

























Отзывы:

Нет отзывов