AuCom EMX3-0053B Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 24

AuCom EMX3-0053B Скачать руководство пользователя страница 2

USER MANUAL

2

Modbus TCP Interface (710-14812-00D)

1.

Warnings

WARNING
For your safety, isolate the soft starter completely from mains voltage before
attaching or removing accessories.

WARNING
Observe all necessary safety precautions when controlling the soft starter
remotely. Alert personnel that machinery may start without warning.

2.

Important User Information

2.1

Safety

It is the installer's responsibility to follow all instructions in this manual and to follow
correct electrical practice.
Close attention is required to the electrical installation and the system design to avoid
hazards either in normal operation or in the event of equipment malfunction. System
design, installation, commissioning and maintenance must be carried out by personnel
who have the necessary training and experience. They must read this safety
information and this guide carefully.

2.2

Product Design

The Modbus TCP Interface allows the soft starter to connect to an Ethernet network
and be controlled or monitored using an Ethernet communication model.

Familiarity with Ethernet protocols and networks is required to operate the device
successfully. For difficulties using this device with third party products, including
PLCs, scanners and commissioning tools, contact the relevant supplier.

«
1
2
3
4
...
»

Содержание EMX3-0053B

























Отзывы:

Нет отзывов