background image

28/33 

 

shelves were empty, the temperature inside the smoker tower is fairly uniform except the 
back half of the lowest shelf that is close to the heater. Users should avoid placing the 
sensor too close to the heater because it does not represent the temperature of the rest 
area. When the shelves are filled, temperature variation might depend on where the food 
is placed. The bottom shelf can become hotter if more food is placed in it to block the hot 
air from going up. 
 

9. Tuning the controller 

This controller is shipped with the system parameters set for the Bradley Smoker. The 
user should not change these parameters if you want to control a Bradley Smoker. 
Otherwise, if you feel that performance is not ideal, you can try to manually tune the 
system or run the auto-tune again. For detailed information on how to tune the controller, 
please read the section 10 for tuning the controller. 
 

10. Auto-Tune   

This section can be ignored if you are using the controller to control the Bradley Smoker 
because the controller already set for it. 

The controller's most powerful feature is its ability to regulate virtually any cooker with 
stable temperature manipulation. For stable temperature control, the controller requires 
two things; (1) the controller must be set to the correct power level (see next section) and, 
(2) that it must be 

tuned 

to the cooker being used. Tuning is the process that matches 

the control characteristics of the controller to the heating characteristics of the cooker. 
The controller is said to be tuned to the cooker when its memory is programmed with 
values telling it how fast the cooker warms up, cools off, and how efficiently it transfers 
heat. For example, consider the difference between a heat lamp and a hot plate. When 
electricity is applied to a heat lamp it begins to heat instantaneously. Additionally, when 
it's turned off, it stops heating instantaneously. In contrast, a hot plate may take several 
minutes to begin heating when electricity is applied and even longer to start cooling 
when electricity is turned off. But to do this, it must be programmed with the time 
constants. Describing how fast the heater heats when electricity is turned on and how 
fast it begins to cool when it's turned off. These time constants are called the 

tuning 

parameters.

 

 
Every type of cooker has its own unique set of tuning parameters. For the controller to 
heat with stability, it must have programmed with the tuning parameters for the cooker 
currently being used.   
 

 
 
 

Содержание AW-WST1510H-W


































Отзывы: