background image

Copyright ©  2021 Auber Instruments Inc. All rights reserved. 

No part of this manual shall be copied, reproduced, or transmitted in any way without the prior, written consent of Auber Instruments.   

Auber Instruments retains the exclusive rights to all information included in this document.

 

Operation Instruction Manual 

Programmable PID Temperature Controller   

WST-1510H / AW-WST1510H-W 

 

Version 1.3 (Nov, 2021) 

 

Auber Instruments 

5755 North Point Parkway, Suite 99 

Alpharetta, GA 30022 

www.auberins.com 

Introduction 

Thank you for purchasing the Auber WS series temperature controller. We sincerely 
appreciate your choice and trust that our product will meet your quality and value 
expectations. At this moment, you may be anxious to operate your own electric smoke 
controller, but a few minutes of your time reading through this manual will only serve to 
enhance your purchase experience. In particular, 

we urge you to read through the 

safety warnings below

. Although this plug-and-play controller is rather simple to 

operate, the process involves high temperature and high wattage appliances, and your 
safety is our number one priority. 

  SAFETY WARNINGS 

 

 

This controller is designed only to be used with devices that have limited power 
and thermal cut off protection, such as thermostats or thermal fuses in case of 
controller failure.   

 

Do not place anything on the top of controller surface, which is used to vent 
excess heat during its operation.   

 

The maximum electric current this controller can handle is 15 Amperes. For 120 
Volts AC in US and Canada, this limits the heater power to 1800 Watts.   

 

Always place the sensor in the controlled subject when the controller is on. Before 
turning on the controller, please make sure the sensor is placed inside the 
container. Leaving the sensor outside of the solution will form an open loop 
operation. If the sensor is left outside, the controller will assume the temperature 
is low even if the controlled subject is already very hot. The controller will provide 
full power to the heater. It will not only overheat the controller, but also damage 
your appliance, and possibly even cause a fire.   

Содержание AW-WST1510H-W


































Отзывы: