Atmel SAM9X25 Скачать руководство пользователя | Manualshive

Страница: 316 / 1145

background image

316

11054A–ATARM–27-Jul-11

SAM9X25

316

11054A–ATARM–27-Jul-11

SAM9X25

Note:

1. A switch, NFD0_ON_D16, enables the user to select NAND Flash path on D0-D7 or D16-D24

depending on memory power supplies. This switch is located in the EBICSA register in the Bus
Matrix user interface.

26.5.2

Product Dependencies

26.5.2.1

I/O Lines

The pins used for interfacing the External Bus Interface may be multiplexed with the PIO lines.
The programmer must first program the PIO controller to assign the External Bus Interface pins
to their peripheral function. If I/O lines of the External Bus Interface are not used by the applica-
tion, they can be used for other purposes by the PIO Controller.

26.5.3

Functional Description

The EBI transfers data between the internal AHB Bus (handled by the Bus Matrix) and the exter-
nal memories or peripheral devices. It controls the waveforms and the parameters of the
external address, data and control buses and is composed of the following elements:

• the Static Memory Controller (SMC)

• the DDR2/SDRAM Controller (DDR2SDRC)

• the Programmable Multi-bit ECC Controller (PMECC)

• a chip select assignment feature that assigns an AHB address space to the external devices

• a multiplex controller circuit that shares the pins between the different Memory Controllers

• programmable NAND Flash support logic

26.5.3.1

Bus Multiplexing

The EBI offers a complete set of control signals that share the 32-bit data lines, the address
lines of up to 26 bits and the control signals through a multiplex logic operating in function of the
memory area requests.

Multiplexing is specifically organized in order to guarantee the maintenance of the address and
output control lines at a stable state while no external access is being performed. Multiplexing is
also designed to respect the data float times defined in the Memory Controllers. Furthermore,
refresh cycles of the DDR2 and SDRAM are executed independently by the DDR2SDR Control-
ler without delaying the other external Memory Controller accesses.

26.5.3.2

Pull-up and Pull-down Control

The EBI_CSA registers in the Chip Configuration User Interface enable on-chip pull-up and pull-
down resistors on data bus lines not multiplexed with the PIO Controller lines. The pull-down
resistors are enabled after reset. The bits, EBIx_DBPUC and EBI_DBPDC, control the pull-up

RAS

VDDIOM

RAS

RAS

–

CAS

VDDIOM

CAS

CAS

–

SDWE

VDDIOM

WE

WE

–

Pxx

VDDNF

–

–

CE

Pxx

VDDNF

–

–

RDY

Table 26-4.

EBI Pins and External Device Connections

Signals:

EBI_

Power supply

Pins of the Interfaced Device

DDR2/LPDDR

SDR/LPSDR

NAND Flash

Controller

DDRC

SDRAMC

NFC

«
...
314
315
316
317
318
...
»

Содержание SAM9X25


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAM9X25

ARM Cortex-A9 MPCore

Бренд: Dave Embedded Systems Страницы: 67

FrameSaver 9120

Бренд: Paradyne Страницы: 2

Бренд: Ubiquiti Страницы: 3

Бренд: Ebyte Страницы: 14

Бренд: Orban Страницы: 255

Бренд: protech Страницы: 95

Бренд: Renesas Страницы: 20

PBE-5AC-300-ISO

Бренд: Ubiquiti Страницы: 28

Бренд: Kontron Страницы: 62

Бренд: ekwb Страницы: 10

ForeFront 2616RC

Бренд: Patton electronics Страницы: 80

Бренд: Transition Networks Страницы: 5

Бренд: NetApp Страницы: 28

Бренд: HeimVision Страницы: 167

Бренд: FOR-A Страницы: 2

Бренд: Crestron Страницы: 22

Бренд: SS Telecoms Страницы: 35

Schottky Barrier Diodes MA3XD21

Бренд: Panasonic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды