Atlas Triton T-80, Руководство по эксплуатации

Страница: 13 / 48

C 11
UL 795. Each unit is constructed in accordance with
Section IV of the American Society of Mechanical Engi-
neers (ASME) Boiler Pressure Vessel Code and bears
the ASME “HLW” stamp or “H” stamp.
C.3. I
NSTALLATION
C
ODES
• Installation of the Triton Series™ boilers must conform
to the require ments of the authority having jurisdiction,
or in the absence of such requirements, to the National
Fuel Gas Code, ANSI Z223.1/ NFPA 54, and/ or
Natural
Gas and Propane Installation Code, CAN/CSA B149.1 .
• Where required by the authority having jurisdiction, the
installation must conform to the Standard for
Controls
and Safety Devices for Automatically Fired Boilers,
ANSI/ASME CSD1
Installations must also follow:
•
Local, state, provincial, and national codes, laws,
regulations and ordinances.
• National Electrical Code, ANSI/ NFPA 70 – latest
edition (NEC).
!
NOTE:
• If any code listed above con ict, the stricter of the
con icting codes shall be followed for installation.
• Installation and Service must be performed by a
quali ed installer, service agency or the gas supplier
C.4. P
REPARING THE
B
OILER
!
NOTE:
Your Atlas™ Triton boiler comes equipped with a steel
pallet jack base for safe and easy movement and place-
ment.
1. Place the boiler in its approximate installed location, on
a clean, level, structurally sound surface.
2. If the boiler is in its original packaging, remove the
banding, carton, corner posts and stand-offs, and
discard.
3. Unpack the manifold assembly from the small carton
attached to the rear of the boiler.
4. Install the manifold assembly to the hot water outlet at
the rear of the boiler until tight, and such that the pres-
sure relief valve is in the vertical, upright position at the
top of the manifold.
5. Install the 2 loose wires at the rear of the boiler to
the ow switch installed at the side of the manifold as
shown in gure C.5.1.
6. Move the boiler to its nal installed position.
!
NOTE:
Ajax Boiler Inc. strongly recommends that you secure the
boiler to the base pad by the mounting holes provided at
the base of the unit.
C.5. W
ATER
S
YSTEM
P
IPING
!
CAUTION:
This boiler requires forced water circulation when burner
is operating. See minimum and maximum ow rates
in Table C.3.1. below. Severe damage will occur if the
boiler is operated without proper water ow circulation.
A ow switch is used to ensure that water ows through
the boiler, but does not check for the minimum ow rate
into the boiler. Numbers are approximate and may vary
depending on installation.
!
NOTE:
Ajax Boiler Inc. strongly recommends that you secure the
boiler to the base pad by the mounting holes provided at
the base of the unit.
All hot water outlet and return piping is connected at the
rear of the boiler. Piping is to be installed per local codes
and regulations. Piping for the hot water outlet and return
may be connected without removing cabinet panels. Un-
used connections must be safely blanked off.
MODEL
T-80 T-100 T-150 T-200
Minimum Flow Rate (GPM): 34 43 65 85
Maximum Flow Rate (GPM): 69 85 129 172
Pressure Drop:
Table C.5.1. Triton Flow Rates.
C.5.a. System Connections
1. Connect cold water return pipe to the primary water
inlet on the boiler.
2. Connect outlet system pipe to hot water outlet at mani-
fold.
3. Install drain valve provided in the boiler drain line at
bottom rear of the boiler.
Ace Heating Solutions, LLC strongly recommends that
you secure the boiler to the base pad by the mounting
holes provided at the base of the unit.
Ace Heating Solutions, LLC strongly recommends that
you secure the boiler to the base pad by the mounting
holes provided at the base of the unit.