Atek HP 8753D, Руководство пользователя, Страница: 661 / 677

modify TRM calibration standards, 5-30
oset limit lines, 2-44
output a single page of values, 4-30
output multiple plots to a single page using
a printer, 4-25
output plot les, 4-20
output plot les from a PC to a plotter,
4-22
output plot les from a PC to a printer,
4-23
output single page plots using a printer,
4-24
output the entire list of values, 4-31
plot a measurement to disk, 4-19
plot measurements in page quadrants,
4-28
plot multiple measurements on a full page,
4-26
plot multiple measurements per page,
4-17, 4-26
plot one measurement per page, 4-16
plot to an HPGL compatible printer, 4-18
power meter calibrate, 3-6
print a sequence, 2-60
print multiple measurements per page,
4-7
print one measurement per page, 4-6
print or plot list values or operating
parameters, 4-30
purge a sequence from disk, 2-60
ratio measurements in channel 1 and 2,
2-7
recall a le, 4-42
reduce receiver crosstalk, 5-57
reduce receiver noise oor, 5-56
reduce the averaging factor, 5-52
reduce the number of points, 5-52
reduce trace noise, 5-57
rename a le, 4-42
re-save a le, 4-41
reset plotting parameters to default values,
4-16
reset the printing parameters to default
values, 4-6
review limit line segments, 2-43
run a limit test, 2-43
run a test sequence, 2-55
save a data trace to the display memory,
2-6
save an instrument state, 4-35
save measurement results, 4-36
search for a target amplitude, 2-24
search for bandwidth, 2-25
search for maximum amplitude, 2-22
search for minimum amplitude, 2-23
sequence tests, 2-53
set auto sweep time mode, 5-51
set center frequency with markers, 2-18
set CW frequency using markers, 2-21
set display reference using markers, 2-20
set electrical delay using markers, 2-21
set frequency range, 2-3
set frequency span with markers, 2-19
set source power, 2-4
set start frequency with markers, 2-17
set stop frequency with markers, 2-17
set the measurement parameters, 2-3
set the measurement type, 2-4
set the sweep type, 5-53
solve printing or plotting problems, 4-32
solve problems with disk storage, 4-43
stop a sequence, 2-55
store a sequence on a disk, 2-59
subtract the memory trace from the
measurement data trace, 2-7
title the active channel display, 2-8
title the displayed measurement, 4-29
track amplitude, 2-25
use analyzer display markers, 2-9
use continuous and discrete markers, 2-9
use delta (1) markers, 2-11
use frequency oset mode, 3-7
use limit lines, 2-36
use
NNNNNNNNNNNNNNNNNNNNNNNNNN
MKR ZERO to activate a xed reference
marker, 2-13
use polar format markers, 2-14
use receiver calibration, 5-11
use Smith chart markers, 2-15
use the tuned receiver mode, 2-51
use the
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
1REF=1FIXED MKR key to activate
a xed reference marker, 2-12
view a single measurement channel, 5-53
view both measurement channels, 2-5
view plot les on a PC, 4-20
view the measurement data and memory
trace, 2-6
widen system bandwidth, 5-52
HP 8753A/B/C/D dierences, 1-13
HPGL
initialization commands, 4-23
outputting plot les to compatible printer
, 4-23
test le commands, 4-24
HPGL/2 compatible printer , conguring to
plot, 4-8
HP-IB, 11-14
address capability, 11-17
addresses, 6-104, 11-20
bus structure, 11-15, 11-16
Index-10