Atek HP 8753D, Руководство пользователя, Страница: 660 / 677

high dynamic range swept RF/IF conversion
loss, 3-12
high-stability frequency reference(10 MHz)
(option 001), 7-34
high stability frequency reference option,
1-12
Hld status notation, 1-8
hold mode , test set switch, 5-54
how to
abort a print or plot process, 4-30
activate a xed marker, 2-11
activate chop sweep mode, 5-54
activate display markers, 2-10
calculate data statistics, 2-26
calibrate the analyzer receiver to measure
absolute power, 5-38
change measurement averaging, 5-56
change system bandwidth, 5-56
change the sequence title, 2-58
clean connectors, 2-2
clear a sequence from memory, 2-57
compensate for directional coupler
response, 5-35
congure a plot function, 4-8
congure a plot function to disk drive,
4-11
congure a plot function using and HPGL/2
compatible printer, 4-8
congure a plot function using a pen
plotter, 4-10, 11-11
congure a print function, 4-3
construct a loop structure in a sequence,
2-62
control the test set switch, 5-54
couple and uncouple display markers, 2-14
create a limit test sequence, 2-64
create a test sequence, 2-54
create at limit lines, 2-37
create single point limits, 2-41
create sloping limit lines, 2-39
decrease frequency span, 5-50
dene line types, 4-14
dene the plot, 4-12
dene the print, 4-5
delete all instrument state les, 4-41
delete an instrument state, 4-41
delete a single instrument state le, 4-41
delete limit segments, 2-42
divide measurement data by the memory
trace, 2-7
edit a sequence, 2-56
edit limit segments, 2-42
edit power calibration factors, 5-34
enter the power sensor calibration data,
5-34
error-correct for frequency response, 5-8
error-correct for frequency response and
isolation, 5-13
error-correct for full two-port
measurements, 5-20
error-correct for one-port reection
measurements, 5-17
error-correct for response and isolation
for reection measurements, 5-13
error-correct for response and isolation
for transmission measurements, 5-15
error-correct for TRL*, 5-23
error-correct for TRM*, 5-23
error-correct measurements, 5-7
error-correct response for reection
measurements, 5-8
error-correct response for transmission
measurements, 5-10
format a disk, 4-43
gate out responses, 2-70
increase sweep speed, 5-50
insert a sequence command, 2-56
load a sequence from disk, 2-60
make a basic measurement, 2-3
make accurate measurements of electrically
long devices, 5-48
measure conversion loss using tuned
receiver mode, 3-17
measure deviation from linear phase, 2-32
measure devices using the time domain,
2-68
measure electrical length and phase
distortion, 2-30
measure xed IF mixers, 3-17
measure gain compression, 2-45
measure group delay, 2-33
measure group delay or phase for mixers,
3-24
measure high dynamic range conversion
loss, 3-12
measure magnitude and insertion phase
response, 2-27
measure mixer isolation, 3-33
measure mixer LO to RF isolation, 3-33
measure mixers, 3-1
measure reection response in time domain,
2-73
measure reverse isolation and gain, 2-49
measure swept harmonics, 2-66
measure swept RF/IF mixers, 3-7
measure transmission response in time
domain, 2-68
modify a sequence command, 2-57
modify calibration standards, 5-26
modify TRL calibration standards, 5-28
Index-9