ASTi ACE Studio Скачать руководство пользователя страница 53

Страница: 53 / 62

11.0 Restore system backup

In the Remote Management System (RMS), the

Restore System Backup

page allows you to

restore a model archive that exists on the Telestra Target. You can also choose to upload a
backup file is saved to the local development workstation.

To restore your system backup files, follow these steps:

1. From the vertical left menu, under

Configuration

, click

Backup Restore

2. On the

System Backup/Restore

page, click

Restore System Configuration

3. To transfer the backup from your local system, upload the backup file to the development

workstation. In the

Upload Previous Backup File

area, click

Choose File

. Browse to

the file location on your computer, and select your system backup.

4. Click

Upload Backup File

, and wait for the upload to complete.

Figure 35: Restore System Backup

5. The backup appears in the

Existing Backup Files

area. To start the installation, locate

your backup name in the list, and click the

restore now

link.

ACE Target and Studio Cold Start Guide (Rev. B, Ver. 0)

Содержание ACE Studio































































Результаты поиска

Содержание ACE Studio

Отзывы:

Похожие инструкции для ACE Studio

Бренды по названию

Популярные бренды

ASTi ACE Studio, Руководство по холодному запуску

Результаты поиска

Содержание ACE Studio

Отзывы:

Похожие инструкции для ACE Studio

Бренды по названию

Популярные бренды