background image

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. 
Copyright © 2010, 2013 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. 
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 

ASSA ABLOY

80-9357-0001-020 (09-13)

Page 2 

Hollow Metal Door Frame Reinforcing

Frame

Material

12 Ga.

.1046

 (2.66)

14 Ga.

.0747

 (1.90)

16 Ga.

.0598

 (1.52)

18 Ga.

.0478

 (1.21)

12 Ga.

.1046

 (2.66)

10 Ga.

.1343

 (3.41)

10 Ga.

.1343

 (3.41)

8 Ga.

.1644

 (4.18)

18 Ga.

.0478

 (1.21)

12 Ga.

.1046

 (2.66)

12 Ga.

.1046

 (2.66)

10 Ga.

.1343

 (3.41)

Reinforcing

Recommended

Min. Required

Contents

General Information

UL labeled fire or smoke barrier door assemblies require that 
the 120VAC (60Hz) power input to the 

LEO

 door operator be 

supplied through normally closed alarm contacts of the alarm 
system / alarm panel.

Power input to 

LEO

 door operator must be 120VAC (60Hz) to 

terminals HOT and COM at terminal strip T1. Earth ground 
(GND) to green screw on backplate.

All wiring must conform to standard wiring practice in 
accordance with national and local wiring codes.

Note: Unless otherwise noted, all dimensions are given in 
inches (millimeters).

Minimum suggested and required material thickness for 
hollow metal frames (skin plus reinforcement) is charted on 
below.

Unit is Non-Handed.

Door must be hung on butt hinges [5” (127mm) max. width] 
or 3/4” (19mm) offset pivots. A separate door and frame 
preparation template will be supplied for other conditions.

Door must swing freely through the entire opening and 
closing cycle before beginning the installation.

Use of an auxiliary door stop (by others) is always 
recommended.

An incorrectly installed or improperly adjusted door operator 
can cause property damage or personal injury. These 
instructions should be followed to avoid the possibility of 
misapplication or misadjustment.

WARNING:

 Make sure 120VAC (60Hz) input power is turned 

off at facility’s main circuit breaker before proceeding with 
installation.

General Templating Information:

Before beginning the installation, verify that the door frame is 
properly reinforced and is well anchored in the wall.

Unreinforced hollow metal frames and aluminum frames 
should be prepared and fitted with 1/4-20 blind rivet nuts, 
furnished by others.

Concealed electrical conduit and concealed switch or sensor 
wires should be pulled to the frame before proceeding.

Fasteners for Frame:

1/4-20 machine screws for hollow metal and aluminum.

No. 14 x 2-3/4” (70mm) long sheet metal screws for wood.

Fasteners for Door:

1/4-20 machine screws.

3/8” diameter x 1-5/8” (41mm) long sex nut.

Electrical Information:

Maximum current draw of unit is 0.6 amps.

Breaker Switch protects the motor assembly and inverter; 
and has a 5 amp rating.

Maximum wire size is:

12AWG at terminals HOT and COM (120VAC; 60Hz) on 

“T1” Power Input Terminal.

14AWG at terminals 1 thru 4 on Accessory Terminal .
18AWG at terminals 22 thru 25 on “T1” Power Input 

Terminal.

Frame Reinforcement Table

General  

 

 

 

 

 

2

Frame Reinforcement Table 

 

 

 

2

Component Layout 

 

 

 

 

3

ADA / ANSI / UL 

 

 

 

 

3

Hinge (Pull) Side Mounting 

 

 

 

4

Hinge (Pull) Side Installation 

 

 

 

4

Stop (Push) Side Mounting 

 

 

 

6

Stop (Push) Side Installation 

 

 

 

6

Electrical Installation 

 

 

 

 

7

Input Power Configuration 

 

 

 

8

Inverter Details   

 

 

 

 

9

Accessory / Typical Installations  

 

 

9

Troubleshooting  

 

 

 

 

11

Содержание Norton 5700 Series













Отзывы: