Ascon Tecnologic - K__V - Indicators - ENGINEERING MANUAL - PAG. 14
[61] PAS3 - Level 3 password : configuration level
Available:
Always.
Range:
From 3 to 999.
Note:
Setting [60] PAS2 equal to [61] PAS3, the level 2 will
be masked.
[62] uSrb - U button function during RUN TIME
Available:
Always.
Range:
nonE = No function
AAc = Alarm reset
ASi = Alarm acknowledge
HoLd = Hold of the measured value
d.Pic = The display will shows the peacks.
r.Pic = Peachs reset
0.Pot = Start the 0.Pot routine
r.Pot = 0.Pot r Peacks reset
t.Pot = Input calibration with self-learning procedure
Str.t = Timer run/hold/reset (see note below).
Note:
When “Timer run/hold/reset” is selected, a short press
starts/stops(hold) timer count while a long press (lon-
ger than 10 second) resets the timer.
Where:
nonE:
no function
Aac:
Pushing for 1 s at least, it is possible to acknowled-
ge the alarm (see par. 4.3).
ASi:
Pushing
for 1 s at least, it is possible to acknowled-
ge an active alarm (see par. 4.3).
HoLd:
Pushing the measurement taken at that moment
is blocked (N.B.: not the reading on the display, there-
fore the indication may stabilise itself with a delay that
is proportional to the measuring filter). With the hold
function turned on, the instrument carries out control
according to the memorised measurement. Releasing
the key, the instrument starts normal measurement
acquisition once more.
d.Pic:
Pressing
, the maximum variation of the measure-
ment recorded since the instrument was switched on
is visualized on the display (highest/lowest peak).
r.Pic:
Pressing
, the highest and lowest peak values are
re-set.
0.Pot:
For the instruments with normalized signals input, it
is possible to set the “zero” value with this function.
Pressing
for at least 1 s, the display will show the
writing “0.Pot” for approx. 1 s and then “0”, assuming
the value measured in that instant as 0. In practice,
this function allows to allign the zero of the readout
scaling (defined by [4] SSc and [5] FSc parameters)
with the current measured value.
An example will help us to show the result.
Input type: 0... 50 mV
[4] SSc = 0
[5] FSc = 100
[65] uSrb = O.Pot
Now, the current position is equal to 30 and I push the
button. The display will show zero and the new
readout range becomes -30... +70°.
r.P0P:
For the instruments with normalized signals input, it
is possible to set the “zero” value and contemporarily
re-set the highest and lowest peak values with this
function. Pressing
for at least 1 s, the display will
show the writing “r.P0P” for approx. 1 s, and then “0”,
assuming the value measured in that instant as 0 and
re-setting the memorized peak values.
t.Pot: For the instruments with normalized signals input, with
this function it is possible to set the points of measu-
rement by means of auto-ranging procedure through
which the parameters “SSC”, “FSC” and “0.Pot.” are
automatically re-calculated.
Pressing
for at least 1 s, the display will show “P1”
alternatively to the value of the first point of setting.
Now, give to the input the first point value of setting
and program the value desired for that point using the
and
keys. Once the value has been set, press
the
key: the instrument will memorize the value
and the display will show “P2” alternatively to the value
of the second point of setting. Give to the input the
second point value of setting and program the value
desired for that point using the
and
keys. Pres-
sing the
key, the second value is also acquired and
the instrument will automatically exit from the self-
learning mode, re-calculating the measuring range.
[63] diSP – Display management
Available:
Always.
Range:
nonE = Standard display
AL1 = Alarm 1 threshold
AL2 = Alarm 2 threshold
AL3 = Alarm 3 threshold
AL4 = Alarm 4 threshold
ti.uP = When the timer is running, the display will
show the timer counting up.
At the end of the counting, the instrument
will show “t.End” messages alternately with
the measured value.
ti.du = When the timer is running, the display will
show the timer counting down.
At the end of the counting, the instrument
will show “t.End” messages alternately with
the measured value.
[64] Edit - Alarm editing enabling
Available:
Always.
Range:
AE =
Alarm thresholds can be modified
AnE = Alarm threshold can NOT be modified
]
Ser group - Serial link parameter
[65] Add - Instrument address
Available:
Always.
Range:
oFF = Serial interface not used
1... 254.
[66] bAud - Baud rate
Available:
When [65] Add different from oFF
Range:
1200 = 1200 baud
2400 = 2400 baud
9600 = 9600 baud
19.2 = 19200 baud
38.4 = 38400 baud
