background image

Ascon Tecnologic - KxxV - Indicators -  ENGINEERING MANUAL -V2.0 PAG. 23

no. Param.

Description

Dec. 

Point

Values

Default

Vis. 

promo

45  tr.F

Independent timer function

0

NonE = Timer not used
i.d.A = Delayed start timer
i.uP.d = Delayed start at power up
i.d.d = Feed-through timer
i.P.L = Asymmetrical oscillator with start in OFF
i.L.P = Asymmetrical oscillator with start in ON

nonE

A-62

46  tr.u

Timer unit

0

hh.nn = Hours and minutes
nn.SS = Minutes and seconds
SSS.d = Second and tenth of seconds

nn.SS

A-63

47  tr.t1

Time 1

2

When tr.u = hh.nn from 00.01 to 99.59
When tr.u = nn.SS from 00.01 to 99.59
When tr.u = SSS.d from 000.1 to 995.9

1.00

A-64

48  tr.t2

Time 2

2

When tr.u = hh.nn from 00.01 to 99.59 + inF
When tr.u = nn.SS from 00.01 to 99.59 + inF
When tr.u = SSS.d from 000.1 to 995.9 + inF

1.00

A-65

49  tr.St

Timer status

0

HoLd = timer hold;
run = timer run;
rES = timer reset

rES

C-0

]

PAn Group - Operator Interface Configuration

no. Param.

Description

Dec. 

Point

Values

Default

Vis. 

promo

50  PAS2

Password level 2

0

From 0 (oFF) to 999 (oFF = Level 2 not protected by psw)

20

A-93

51  PAS3 

Password level 3

0

From 3 to 999

30

C-0

52  uSrb

 button function during run 

time

0

nonE = No function
AAc = Alarm reset
ASi = Alarm acknowledge
HoLd = Hold of the measured value
d.Pic = The display will shows the peaks
r.Pic = Peaks reset
0.Pot = Start the 0.Pot routine
r.Pot = 0.Pot r Peaks reset
t.Pot = Input calibration with self-learning procedure
Str.t = Timer run/hold/reset

nonE

A-94

53  diSP

Display management

0

nonE = Standard display
AL1 = Alarm 1 threshold
AL2 = Alarm 2 threshold
AL3 = Alarm 3 threshold
ti.uP = Timer time up
ti.du = Timer time down

nonE

A-95

54  Edit

Alarm editing enable

0

AE = Alarm thresholds can be modified
AnE = Alarm threshold can NOT be modified

ANe

]

Ser Group - Serial Communications Interface Configuration

no. Param.

Description

Dec. 

Point

Values

Default

Vis. 

promo

55  

Add

Address 

0

0 (oFF)...  254

1

C-0

56  bAud 

Baud rate

0

1200 (bit/s);
2400 (bit/s);
9600 (bit/s);
9.2 (kbit/s);
38.4 (kbit/s)

9600

C-0

Содержание 3 V Series

























Отзывы: