manualshive.com logo in svg

Asante IntraCore 3624, Руководство пользователя

Поделиться
Скачать
Asante IntraCore 3624 Скачать руководство пользователя страница 71

 

VLANs are based on untagged port groups, or traffic can be explicitly tagged to identify the VLAN group to which it 
belongs. Untagged VLANs can be used for small networks attached to a single switch. Tagged VLANs should be 
used for larger networks, and all the VLANs assigned to the inter-switch links.  

A VLAN is a group of end stations with a common set of requirements, independent of physical location. VLANs have 
the same attributes as a physical LAN but allow you to group end stations even if they are not located physically on 
the same LAN segment.  

VLANs are usually associated with IP subnetworks. For example, all the end stations in a particular IP subnet belong 
to the same VLAN. Traffic between VLANs is assigned. LAN port VLAN membership is assigned manually on an 
port-by-port basis. VLANs can be defined as either Layer 2 or Layer 3 and a VLAN cannot switch between the two 
layers. Before you create a VLAN, you must decide how they will be created and a naming convention to ensure 
duplicate VLAN names are not used. 

Up to 4094 Virtual LANs (VLANs) are supported on the IntraCore IC3624/48. The default VLAN with VLAN ID (VID) 
1. All switchports (eth1–eth24) are included in the default VID 1. 

The

 

default VID 1 cannot be deleted

. 

Use this screen to view VLAN information and create a VLAN group. At the top of the main VLAN screen you can 
toggle between VLAN group information and VLAN port information by click on each link. 

VLANs can be created one at a time, or a range of VLANS can be created all at once.   

 

 

 

71 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Содержание IntraCore 3624


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды