manualshive.com logo in svg

Asante IntraCore 3624, Руководство пользователя

Поделиться
Скачать
Asante IntraCore 3624 Скачать руководство пользователя страница 22

 

3.2 Connecting to a PC 

You can connect to the switch through a PC by using either an Ethernet or USB cable. Using a telnet session, you 
can telnet into the switch. The default IP address is 192.168.0.1. The case-sensitive default password is Asante. 

3.3 Username and Password 

The default Username/Password is admin/Asante. 

 

3.4 Configuring an IP Address

 

The switch ships with the default IP address 

192.168.0.1/255.255.255.0

. Connect through the serial port in order to 

assign the switch an IP address on your network. 

The physical ports (or switchports) of the IntraCore 3624/48 are L2 ports, and cannot have an IP address assigned to 
them. By default, each switchport belongs to VLAN 1. Use the following instructions to configure an IP address to the 
switch. Follow the steps below to change the switch’s IP address. 

 

1.

 

Connect to the console and Enter

 

at the Username prompt the username and password as described above. 

2.

 

The screen displays the user mode prompt, 

COMMAND>

. 

3.

 Type 

enable

.  Enter username and password. The new prompt is 

Switch#

. 

4.

 Type 

configuration

. The new prompt is 

Switch(config)#

. 

5.

 

 Type network parms <ip address> <subnet mask> <default gateway> 

 

Switch# 

configuration

 

Switch(config)# network parms 

192.168.0.10 255.255.255.0 192.168.0.254

 

Switch(config)# 

exit

 

Switch# 

save

 

Switch# 

show network  

        MAC Address: 00-03-6d-ff-ef-4c 

        Management VLAN: 1 

        STATIC 

        IP: 192.168.0.10 

        Netmask: 255.255.255.0 

        Gateway: 192.168.0.254

 

 

 

 

22 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Содержание IntraCore 3624


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды