Asante IntraCore 3624 Скачать руководство пользователя страница 121

Страница: 121 / 145

Mode

Global Config

10.4.10.3 mgmt-accesslist disable

This command disables management access list.

Format

mgmt-accesslist disable

Mode

Global Config

10.4.11 monitor commands
10.4.11.1 monitor enable

This command enables port mirroring.

Format

monitor enable

Mode

Global Config

10.4.11.2 monitor disable

This command disables port mirroring.

Format

monitor disable

Mode

Global Config

10.4.11.3 monitor des

Configure destination port.

1) monitor des <port-ID> probetype bidirection

This command configures port monitor probetype as bi-direction traffic.

Format

monitor des <

port-ID

> probetype bidirection src <

port list

Mode

Global Config

e.g. Switch(config)# monitor des 1 probetype bidirection src 2-8

2) monitor des <port-ID> probetype ingress

This command configures port monitor probetype as ingress traffic.

Format

monitor des <

port-ID

> probetype ingress src <

port list

Mode

Global Config

e.g. Switch(config)# monitor des 1 probetype ingress src 2-8

3) monitor des <port-ID> probetype egress

This command configures port monitor probetype as egress traffic.

Format

monitor des <

port-ID

> probetype egress src <

port list

Mode

Global Config

e.g. Switch(config)# monitor des 1 probetype egress src 2-8

10.4.12 dot1x commands
10.4.12.1 dot1x enable

This command enables global 802.1x function.

Format

dot1x enable

Mode

Global Config

10.4.12.2 dot1x disable

This command disables global 802.1x function.

Format

dot1x disable

Mode

Global Config

10.4.12.3 dot1x port-control

Configure port auto-authentication mode.

1) dot1x port-control enable

This command set auto-authorized on a list of ports.

Format

dot1x port-control enable port <

port list

Mode

Global Config

2) dot1x port-control disable

This command set force authorized on a list of ports.

Format

dot1x port-control disable port <

port list

Mode

Global Config

29
e.g. Switch(config)# dot1x port-control disable port 1-4

10.4.13 network commands
10.4.13.1 network mgmt-vlan

This command changes management vlan.

121

Asante IntraCore IC3624/48

User’s Manual

Содержание IntraCore 3624


















































































































































Результаты поиска

Содержание IntraCore 3624

Отзывы:

Бренды по названию

Популярные бренды

Asante IntraCore 3624, Руководство пользователя

Результаты поиска

Содержание IntraCore 3624

Отзывы:

Бренды по названию

Популярные бренды