Asante IntraCore 3624 Скачать руководство пользователя страница 113

Страница: 113 / 145

This command display dot1x and port configuration

Format

show dot1x config

Mode

Privileged Mode

2) show dot1x radius

This command display radius configuration

Format

show dot1x radius

Mode

Privileged Mode

3) show dot1x statistics

This command display dot1x statistics

Format

show dot1x statistics

Mode

Privileged Mode

10.3.11.3 show igmp snooping

This command display IGMP snooping information

1) show igmp snooping dynamic_router_port

This command display dynamic router ports information

Format

show

igmp

snooping dynamic_router_port

Mode

Privileged Mode

2) show IGMP snooping groups

This command is used to display

igmp

groups information

Format

show IGMP snooping groups

Mode

Privileged Mode

10.3.11.4 show interface

This command is used to display summary statistics

1) show interface history

This command is used to display port RX and TX

Format

show interface history <

port-ID

Mode

Privileged Mode

2) show interface statistics

This command is used to display port summary statistics

Format

show interface statistics <

port-ID

Mode

Privileged Mode

10.3.11.5 show lag

This command is used to display link aggregation groups information

1) show lag lag-index

This command is used to specify an switch lag

Format

show lag lag-index <

port-ID

Mode

Privileged Mode

2) show lag all

This command is used to display all switch lag

Format

show lag all <

port-ID

Mode

Privileged Mode

10.3.11.6 show lldp

This command is use to display lldp statistics

1) show lldp statistic

This command is used to display lldp statistic

Format

show lldp statistic

Mode

Privileged Mode

2) show lldp local

This command is used to display local information

Format

show lldp local

Mode

Privileged Mode

3) show lldp msap

This command is used to display msap information

Format

show lldp msap

Mode

Privileged Mode

113

Asante IntraCore IC3624/48

User’s Manual

Содержание IntraCore 3624


















































































































































Результаты поиска

Содержание IntraCore 3624

Отзывы:

Бренды по названию

Популярные бренды

Asante IntraCore 3624, Руководство пользователя

Результаты поиска

Содержание IntraCore 3624

Отзывы:

Бренды по названию

Популярные бренды