manualshive.com logo in svg

Asante IntraCore 3624, Руководство пользователя

Поделиться
Скачать
Asante IntraCore 3624 Скачать руководство пользователя страница 109

 

Chapter 10: CLI Commands 

The CLI is divided into various modes. The Commands in one mode are not 
available until the operator switches to that particular mode. The commands 
available to the operator at any point in time depend upon the mode. Entering 
a question mark (?) at the CLI prompt, and displays a list of the available 
commands and descriptions of the commands. 
The CLI provides the following modes. 
 
 

10.1 Modes 

 
When the operator logs into the CLI, the User Mode is the initial mode. The 
User Mode contains a limited set of commands. The command prompt shown 
at this level is: 

Command Prompt: COMMAND> 
Privileged Mode 

To have access to the full suite of commands, the operator must enter the 
Privileged Mode. The Privileged Mode requires password authentication. From 
Privileged Mode, the operator can issue any Exec command to enter the 
Global Configuration mode. The command prompt shown at this level is: 

Command Prompt: Switch# 
Global Config Mode 

This mode permits the operator to make modifications to the running 
configuration. General setup commands are grouped in this mode. From the 
Global Configuration mode, the operator can enter the Interface Configuration 
mode. The command prompt at this level is: 

Command Prompt: Switch(Config)# 

From the Global Config mode, the operator may enter the following 
configuration modes: 
14 

Interface Config Mode 

Many features are enabled for a particular interface. The Interface commands 
enable or modify the operation of an interface. In this mode, a physical port is 
set up for a specific logical connection operation. The command prompt at this 
level is: 

Command Prompt: Switch(Interface <port#>)# 
 
 

10.2 User Mode commands 

 
10.2.1 Help 

This command displays help information 

Format 

help 

Mode 

User Mode 

10.2.2 ? 

This command displays help information 

Format 

help 

Mode 

User Mode 

10.2.3 logout 

This command is used to exit from the telnet 

Format 

logout 

Mode 

User Mode 

10.2.4 ping 

This command sends echo messages. 

109 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Содержание IntraCore 3624


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды