manualshive.com logo in svg

Asante IntraCore 3624, Руководство пользователя

Поделиться
Скачать
Asante IntraCore 3624 Скачать руководство пользователя страница 38

 

Switch# 

clear config

 

 

Don’t forget to use ‘

save’

 command to preserve the new configuration across reboots. 

 

5.3 Managing system image Files 

This system image file is stored in the non-volatile flash in the switch. It is the software that runs in the switch after 
power up. It provides user interfaces (CLI, Web, telnet) for user to control and manage the switch. The following 
describes the commands that save the system image to a file in a host TFTP server and download a new version 
system image from a TFTP server to the switch. 

5.3.1 Saving System image to a Network Server 

You can save the system image file of the switch to a file server using TFTP. You might wish to back up the current 
system image file to a server , thereby allowing you to later restore the original system image from the server in case 
of system image file corruption. 

To save the system image file of the switch to a TFTP server, use one of the following commands in EXEC mode: 

Command Purpose 

copy system_image tftp 192.168.0.254 file ttt sysimg_file 

Copy the system image the file ‘sysimg_file’ to 
TFTP server 192.168.0.254. 

 
5.3.2 Replacing System image  from a Network Server 

You can replace the system image file of the switch from a file in a server using TFTP. You can update the current 
system image with a newer version in this fashion. 

To replace the system image file of the switch from a TFTP server, use one of the following commands in EXEC 
mode: 

Command Purpose 

copy tftp 192.168.0.254 file new_sysimg system_image 

Copy the system image the file ‘new_sysimg’ from 
TFTP server 192.168.0.254 to the switch. 

 
5.4 Configuring SNMP  

This section discusses the following tasks needed to configure Simple Network Management Protocol (SNMP). 

38 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Содержание IntraCore 3624


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды