manualshive.com logo in svg

Asante IntraCore 3624, Руководство пользователя

Поделиться
Скачать
Asante IntraCore 3624 Скачать руководство пользователя страница 49

 

 

Enable  the IGMP querier 

Multicast switches can send IGMP host-query messages to discover which multicast groups are present on attached 
networks. These messages are sent to the all-systems group address of 224.0.0.1 with a time-to-live (TTL) value 
of 1. 

Multicast switches continue to periodically send host-query messages to refresh their knowledge of memberships 
present on their networks. If, after some number of queries, the switch software discovers that no local hosts are 
members of a multicast group, the software stops forwarding onto the local network multicast packets from remote 
origins for that group and sends a prune message upstream toward the source. 

The switch can be configured to send IGMP queries which are used to solicit IGMP hosts report messages. The 
switch uses the report messages to keep track of which ports belong to which IP multicast group. 

To enable/disable IGMP querier , use the command below: 

Command Purpose 

set igmp-querier {enable | disable}

 

Enable/Disable IGMP querier  

 

Modifying the IGMP Host-Query Message Interval 

Multicast switches elect a designated switch for the LAN (subnet). The designated switch is the one with the highest 
IP address. The switch is responsible for sending IGMP host-query messages to all hosts on the LAN. By default, the 
designated switch sends IGMP host-query messages every 60 seconds in order to keep the IGMP overhead on hosts 
and networks very low. To modify this interval, use the following command in interface configuration mode: 

Command Purpose 

set  igmp query-interval <10-3600

 

seconds>

 

Configure the frequency at which the designated switch sends 
IGMP host-query messages. 

 
The following example shows setting the IGMP query interval to 200. 

Switch(config)# 

set igmp query-interval 200

 

 

Changing the Maximum Query Response Time 

By default, the maximum query response time advertised in IGMP queries is 10 seconds. If the switch is using IGMP 
Version 2, you can change this value. To change the maximum query response time, use the following command in 
configuration mode: 

Command Purpose 

set igmp  query-resinterval <0-200 seconds> 

Set the maximum query response time advertised 
in IGMP queries. 

49 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Содержание IntraCore 3624


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды