Asante IntraCore 3624 Скачать руководство пользователя страница 131

Страница: 131 / 145

This command clears TCP/UDP destination port filter.

Format

access-list name <

WORD

> clear l4port DST port

Mode

Global Config

4) access-list name <WORD> clear packet-type

This command clears packet type filter.

Format

access-list name <

WORD

> clear packet-type

Mode

Global Config

5) access-list name <WORD> clear mac SA

This command clears a source mac address.

Format

Access-list name <

WORD

> clear mac SA

Mode

Global Config

6) access-list name <WORD> clear MAC DA

This command clears a destination mac address.

Format

Access-list name <

WORD

> clear mac DA.

Mode

Global Config

7)access-list name <WORD> clear VID

This command clears the 802.1Q VLAN tag of packet.

Format

Access-list name <

WORD

> clear VID

Mode

Global Config

8)access-list name <WORD> clear ether-type

This command clears ether type filter.

Format

access-list name <

WORD

> clear ether-type

Mode

Global Config

10.4.23.4 access-list name <WORD> deletes.

This command removes the ACL entry.

Format

access-list name <

WORD

> deletes

Mode

Global Config

10.4.23.5 access-list name <WORD> {enable|disable}

This command enables/disables the ACL entry.

Format

access-list name <

WORD

> {enable|disable}

Mode

Global Config

10.4.23.6 access-list name <WORD> set
1) access-list name <WORD> set priority

This command specifies ACL entry priority.

Format

access-list name <

WORD

> set priority <0-65535>

Mode

Global Config

2) access-list name <WORD> set IP-mode
access-list name <WORD> set IP-mode SRC IP.

This command specifies a source IP address.

Format

access-list name <

WORD

> set IP-mode SRC IP <IP-addr>

mask-addr

Mode

Global Config

access-list name <WORD> set IP-mode DST IP

This command specifies a destination IP address.
41

Format

access-list name <

WORD

> set IP-mode DSP IP <

IP-addr

mask-addr

Mode

Global Config

3) access-list name <WORD> set L4port

This command specifies the TCP/UDP port range.

access-list name <WORD> set l4port SRC-port

This command specifies the source TCP/UDP port range.

Format

Access-list name <

WORD

> set L4 port SRE-port from <1-65535>

to <1-65535>

Mode

Global Config

131

Asante IntraCore IC3624/48

User’s Manual

Содержание IntraCore 3624


















































































































































Результаты поиска

Содержание IntraCore 3624

Отзывы:

Бренды по названию

Популярные бренды

Asante IntraCore 3624, Руководство пользователя

Результаты поиска

Содержание IntraCore 3624

Отзывы:

Бренды по названию

Популярные бренды