Arkray AUTION ELEVEN AE-4022, Краткое руководство пользователя

Страница: 24 / 26

14
SEMI-AUTOMATED URINE ANALYZER
AUTION ELEVEN
™
AE-4022
Errors
Message Error Possible cause Measures (Corrective Action)
E001 Power down
The instrument was suddenly turned OFF
during measurement.
Retest the sample(s) currently being measured.
E002
Backup
memory error
As the instrument was unused for a long
period, the memory backup battery was
exhausted and the measurement result stored
in the memory were lost.
Keep the instrument powered for at least 11 hours
to charge the backup battery. After charging the
instrument, set the date and time.
E004
No paper in
the printer
• The thermal recording paper has run out.
• The thermal recording paper roll was not
properly installed.
• Install a new roll of thermal recording paper.
• Make sure the thermal recording paper is installed
correctly.
E005
Waste box
is full At the end of the measurement, the test
strip waste counter exceeded 90.
Cancel the error notice by pressing
4.2 Replacing the thermal recording paper
AE-4022
4-13
3 Prepare a new roll of thermal recording paper
a
Cut the first (outermost) layer of a new thermal recording paper
roll, and trim the end to make it straight. A skewed or odd-shaped
end may cause the thermal recording paper to jam.
4 Set the new thermal recording paper roll
a
Place the new roll of thermal recording paper in the paper holder,
orienting it correctly so that the paper feeds from the bottom.
Guide the trimmed end of the thermal recording paper into and
through the slot that receives the recording paper.
The thermal recording paper is automatically wound forward and
fed into the unit.
NOTE:
When the thermal recording paper is completely removed
from the printer, the screen message shown in the right
figure appears and a continuous beep sounds for
approximately 1 minute. The alarm sound can be stopped
by pressing
.
Paper holder
Set the new roll of thermal
recording paper in the
paper holder in the proper
orientation so that the end
feeds from the bottom.
NOTE:
Always press the button after replacing the thermal
recording paper.If you
do not
fully feed the thermal
recording paper through the unit by pressing the button,
the printer will fail to print the measurement results.
REFERENCE:
If the printer fails to properly wind and feed the thermal recording paper, press and verify that the paper feeds
correctly.
. Empty the
used test strips from the waste box, and press
➀
.
E006
Surplus urine
is full
At the end of the measurement, the total
number of measurements since turning ON the
instrument exceeded 190.
Turn OFF the instrument and discard any surplus urine
from the suction port.
Errors may occur when you operate the instrument incorrectly or make a mistake
during normal operation. When an error occurs, an error message appears on the
screen and an alarm sounds for approximately 1 minute.
Press
4.2 Replacing the thermal recording paper
AE-4022
4-13
3 Prepare a new roll of thermal recording paper
a
Cut the first (outermost) layer of a new thermal recording paper
roll, and trim the end to make it straight. A skewed or odd-shaped
end may cause the thermal recording paper to jam.
4 Set the new thermal recording paper roll
a
Place the new roll of thermal recording paper in the paper holder,
orienting it correctly so that the paper feeds from the bottom.
Guide the trimmed end of the thermal recording paper into and
through the slot that receives the recording paper.
The thermal recording paper is automatically wound forward and
fed into the unit.
NOTE:
When the thermal recording paper is completely removed
from the printer, the screen message shown in the right
figure appears and a continuous beep sounds for
approximately 1 minute. The alarm sound can be stopped
by pressing
.
Paper holder
Set the new roll of thermal
recording paper in the
paper holder in the proper
orientation so that the end
feeds from the bottom.
NOTE:
Always press the button after replacing the thermal
recording paper.If you do not fully feed the thermal
recording paper through the unit by pressing the button,
the printer will fail to print the measurement results.
REFERENCE:
If the printer fails to properly wind and feed the thermal recording paper, press and verify that the paper feeds
correctly.
to cancel the error notice. The display returns to the [Standby screen].
To prevent the error from recurring, take appropriate measures (corrective action),
referring to the table below. If unable to clear the error, note error code and call
ARKRAY Technical Support at 1.855.646.3108.
5.2 Error messages
AE-4022
5-3
5.2 Error messages
Errors may occur when you operate the instrument incorrectly or make a mistake during normal operation.
When an error occurs, an error message appears on the screen and an alarm (pi-pi-pi-pi) sounds for approximately 1
minute.
Press to cancel the error notice. The display returns to the [Standby screen].
To prevent the error from recurring, take appropriate measures, referring to the table below. Alternatively, note the
details of the situation at hand, turn OFF the instrument, and contact your local distributor.
Message Error Possible cause Measures
E001 Power down The instrument was suddenly turned
OFF during measurement.
Retest the sample(s) currently being
measured.
E002 Backup memory error As the instrument was unused for a
long period, the memory backup
battery was exhausted and the
measurement results stored in the
memory were lost.
Keep the instrument powered for at
least 11 hours to charge the backup
battery. After charging the instrument,
set the date and time. (See page 3-11.)
E004 No paper in the printer • The thermal recording paper has
run out.
• The thermal recording paper roll
was not properly installed.
• Install a new roll of thermal recording
paper. (See page 4-12.)
• Make sure the thermal recording
paper is installed correctly.
E005 Waste box is full At the end of the measurement, the
test strip waste counter exceeded 90.
Cancel the error notice by pressing
. Empty the used test strips from the
waste box, and press .
E006 Surplus urine is full At the end of the measurement, the
total number of measurements since
turning ON the instrument exceeded
190.
Turn OFF the instrument and discard
any surplus urine.
E007 Data not found No data was found in the specified
range.
Verify that the specified range for
re-printing, re-sending, or list printing is
appropriate.
E008 Auto start sensor error • A test strip was placed while the
carrying arm was moving to the
suction ports.
• The detection section of the auto
start sensor was soiled with urine.
• The auto start sensor is faulty.
• Remove the test strip.
• Clean the detection section.
• If you find no abnormality and the
error recurs, contact your local
distributor.
E009 No test strip on the
feeder
• The feed lever is not attached.
• The incoming strip sensor is faulty.
• The sensor failed to detect a test
strip.
• Turn OFF the instrument and open
the maintenance cover.
• Mount the feed lever.
• If you find any obstacles or scattered
test strips inside, remove them.
• If you find no abnormality and the
error recurs, contact your local
distributor.
E011 Elapse of QC deadline The QC deadline elapsed while the
instrument was OFF or on standby.
Perform control measurements.