Aristo ARISTOMAT CL 1310 Скачать руководство пользователя

Страница: 52 / 56

ARISTOMAT CL

Technical Hints

Fault

TOOL ERROR HIGH
POSITION PRESS
ESC TO CONTINUE

OTHER TOOL ERRORS
PRESS ESC
TO CONTINUE

TOOL ERROR ON
TURNING PRESS
ESC TO CONTINUE

TOOL ERROR LOW
POSITION PRESS
ESC TO CONTINUE

Drive fault

EMERGENCY-STOP
FAULT X-AXIS / AIR
PRESSURE

X-AXIS SERVO-AMPLIFIER
NOT READY

ERROR X-AXIS INTEGRAL
PRESS ESC-KEY

ERROR Y-AXIS INTEGRAL
PRESS ESC-KEY

ERROR X-AXIS DIFF.
PRESS ESC-KEY

ERROR Y-AXIS DIFF.
PRESS ESC-KEY

ERROR IO-BOARD
SWITCH ON PLOTTER
AGAIN

ERROR Y-BOARD SWITCH
ON PLOTTER AGAIN

Cause

1.The axis are blocked

2.Defective machine control

3.The material is too thick

1.The motor’s temperature is
too high

2.There is not enough com-
pressed air

1.The amplifier is either
overloaded or defective

1.Blocking of the axis due to
material

2.Defective machine control

3.Feeding speed and/or
acceleration is too high

1.Defective machine control

Remedy

1.Switch off drives and
check tool. Press ESC and
switch on drives to continue

2.Choose menu SETTINGS,
MATERIAL Thickness

3.Mount the tool head in a
higher position

1.Switch off the ARISTOMAT
and cool down the motor

2.Increase compressed air
setting at maintenance unit
or compressor

1.Switch the ARISTOMAT off
and on

1.Remove the blocking
material from the axis. Press
ESC and switch on drives
again

2.Call a service technician

3.Reduce parameters FEED
and ACCELERATION

1.Call a service technician

Содержание ARISTOMAT CL 1310

























































Результаты поиска

Содержание ARISTOMAT CL 1310

Отзывы:

Похожие инструкции для ARISTOMAT CL 1310

Бренды по названию

Популярные бренды

Aristo ARISTOMAT CL 1310, Руководство пользователя

Результаты поиска

Содержание ARISTOMAT CL 1310

Отзывы:

Похожие инструкции для ARISTOMAT CL 1310

Бренды по названию

Популярные бренды