manualshive.com logo in svg

Ariens Pro 28 EFI CE, Руководство по обслуживанию, Страница: 43 / 84

Поделиться
Скачать
Ariens Pro 28 EFI CE Скачать руководство пользователя страница 43

EN – 42

See Figure 89.

IMPORTANT: 

Two flat steel washers will become free 

when short axle is removed.
7.

Hold differential gear and remove short axle.

See Figure 90.
8.

Remove hardware securing axle bearing and bearing 
plate to frame.

IMPORTANT: 

The bearing plate is not a wear item and is 

not necessary to replace.
9.

Remove axle bearing.

Install Right Axle Bearing

1.

Align bearing with bearing plate and mount to frame 
with three hex bolts from inside frame. Secure with 
three locking nuts.

See Figure 91.

IMPORTANT: 

Make sure sleeve bushings remain inside 

short axle.
2.

Reinstall short axle until a small portion of axle is 
through frame.

3.

Reinstall two flat steel washers onto short axle.

4.

Align differential gear with pinion gear and short axle 
and reinstall axle into differential.

Figure 89

Figure 90

Figure 91

1. Short Axle
2. Flat Steel Washer
3. Differential Gear
4. Pinion Gear

1

3

2

4

Содержание Pro 28 EFI CE





















































































Отзывы:

Нет отзывов