Ariens Pro 28 EFI CE Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 84

Ariens Pro 28 EFI CE Скачать руководство пользователя страница 10

EN – 9

IMPORTANT:

Discharge chute control designs differ based

on serial number. Generation 2 chute control designs
appear as shown in Figure 4 and Generation 3 chute
control designs appear as shown in Figure 5. Continue to
step 6 for service to units with Generation 2 designs and
advance to step 10 for service to units with Generation 3
designs.

Generation 2 Chute Control Designs

See Figure 4.
6.

Remove hairpin and cable eyelet from chute control
assembly.

7.

With a pliers, compress cable anchor tabs and remove
anchor from chute control assembly.

8.

Guide cable end through hole in dash panel.

IMPORTANT:

Reinstall hairpin into clevis pin so it is not

misplaced.

9.

Advance to step 13.

Generation 3 Chute Control Designs

See Figure 5.
10. Remove hairpin from clevis pin and partially remove

clevis pin from chute control assembly.

IMPORTANT:

Chute control will come apart if clevis pin is

fully removed.
11. With a pliers, compress cable anchor tabs and remove

anchor from chute control assembly.

12. Guide cable end through hole in dash panel.

IMPORTANT:

Reinstall hairpin into clevis pin so it is not

misplaced.

Figure 4

Generation 2 Chute Control Design

Figure 5

1. Clevis Pin
2. Cable Anchor

Generation 3 Chute Control Design

«
...
8
9
10
11
12
...
»

Содержание Pro 28 EFI CE





















































































Отзывы:

Нет отзывов