APRILIA RSV 1000 R FACTORY Скачать руководство пользователя | Manualshive

Страница: 87 / 148

background image

87

use and maintenance

RSV 1000 R

- RSV 1000 RFACT

USA

USA

IDENTIFICATION DATA

It is a good idea to write down the frame
and engine numbers in the space provided
below. Use the frame number (VIN) to
identify your vehicle when ordering spare
parts.

WARNING

In all states and countries, it is against
the law to alter the Vehicle Identification
Number (VIN). You can incur severe
penalties by doing this. Also, this will
immediately invalidate your warranty.

FRAME NUMBER

The frame number (1) is stamped on the
right side of the fork head.

Frame no. ________________________

ENGINE NUMBER

The engine number (2) is stamped on the
rear part of the left engine crankcase.

Engine no. ________________________

JOINTS WITH CLICK CLAMPS AND
WITH SCREW-TYPE CLAMPS

CAUTION

Remove ONLY the clamps indicated in
the maintenance procedures. The
following text does not authorize the
arbitrary removal of the clamps present
on the vehicle.

WARNING

Before removing a clamp, make sure
that the removal does not cause any
f l u i d l e a k a g e ; i f s o , p r o v i d e f o r
preventing such leakages and protect
the parts placed around the joint.

CLICK CLAMPS

For the removal it is sufficient to use simple
pliers, while for the installation a special
tool is required (see below).

Before removing a clamp, prepare the
m a t e r i a l n e c e s s a r y f o r t h e c o r r e c t
installation of the new clamp.

NOTE

Have the appropriate special tool



available: - click clamp installation

pliers, see page 47 (SPECIAL TOOLS



).

CAUTION

Upon installation, replace the click
clamp that has been removed with a
ne w clic k c l am p ha ving the sa me
dimensions, available from your Local

aprilia

Dealer.

Do not attempt to reinstall the removed
click clamp, since it is unusable. Do not
replace the removed click clamp with a
screw-type clamp or with other types of
clamps.

CAUTION

Proceed with care, in order not to
damage the joint components.

u

Work with the pliers on the head of the
click clamp, forcing until you release it.

SCREW-TYPE CLAMPS

For the removal and installation it is
sufficient to use a simple screwdriver.

CAUTION

Check the conditions of the screw-type
clamp and if necessary replace it with a
new screw-type clamp of the same
dimensions, available from your Local

aprilia

Dealer.

When fastening the screw-type clamp,
make sure that the joint is sufficiently
stable.

APRum_RSV1000R##06_####.book Page 87 Monday, February 6, 2006 2:48 PM

«
...
85
86
87
88
89
...
»

Содержание RSV 1000 R FACTORY





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSV 1000 R FACTORY

Бренд: Xenith Страницы: 17

Бренд: BMW Motorrad Страницы: 143

Бренд: Nolan Страницы: 80

Бренд: Rivco Страницы: 5

Бренд: paladin Страницы: 2

Бренд: N-Com Страницы: 2

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 100

Road Star XV17AWX

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 650

Бренд: PUIG Страницы: 2

Бренд: hepco & becker Страницы: 5

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 304

Бренд: Chicago Electric Страницы: 12

gtrack 7855 MyBASIC

Бренд: Gemini Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды