APRILIA RSV 1000 R FACTORY Скачать руководство пользователя | Manualshive

Страница: 107 / 148

background image

107

use and maintenance

RSV 1000 R

- RSV 1000 RFACT

USA

USA

u

Pull the wheel backwards, removing it from
the swing arm from behind, carefully
removing the disc from the brake caliper.

NOTE

The left spacer ring (10) and the

right spacer ring (11) remain locate in their
seats on the wheel; but if they have come
out of their seats retrieve them.

NOTE

The torque plate (12) of the brake

caliper (13) remains installed on the right
side of the rear fork.

Proceed with care. If the final drive unit
(14) is installed on the flexible coupling
holder (15), do not overturn or rotate the
rear wheel in horizontal position on the rear
sprocket side (A), since the final drive unit
would come off and fall, and this may
damage the rear sprocket (9).

NOTE

If the wheel is in the normal

running position (vertical) or in horizontal
position with the rear sprocket facing
upwards and in both c ases secur ed
against overturning, it is not necessary to
remove the final drive unit.

NOTE

Do not unscrew the five nuts (16).

The complete final drive unit must be
withdrawn from the flexible coupling
holder.

u

Working (B) with both hands on the outer
diameter of the sprocket (9), withdraw
the final drive unit parallely to the wheel
axis.

REASSEMBLY

If the final drive unit has been removed
(14):

NOTE

Introduce the final drive unit,

parallely to the wheel axis, inserting the
flexible couplings in the corresponding
seats on the flexible coupling holder (15).

u

Working (C) with both hands on the
outer diameter of the sprocket (9), insert
the final drive unit in the flexible coupling
holder (15).

CAUTION

While reassembling the rear wheel, be
careful not to damage the brake line, the
disc and the pads.

NOTE

Perform the follow operation only if

the left spacer ring (10) and/or the right spacer
ring (11) have come out of their seats on the
wheel:

u

Install the left (10) and right (11) spacer
rings in their seats on the wheel with the
larger diameter towards the outside of the
vehicle (see figure).

CAUTION

Before proceeding with the reassembly,
make sure that the torque plate (12) of the
brake caliper (13) is positioned correctly;
the plate slot must be inserted in the
appropriate stop pin (17) in the inner part
of the right side of the swinging arm. Insert
the disc in the brake caliper carefully.

18

APRum_RSV1000R##06_####.book Page 107 Monday, February 6, 2006 2:48 PM

«
...
105
106
107
108
109
...
»

Содержание RSV 1000 R FACTORY





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSV 1000 R FACTORY

990 Adventure Baja

Бренд: KTM Страницы: 227

Бренд: Ohlins Страницы: 8

TwinSpark Super head plus R

Бренд: Takegawa Страницы: 5

Бренд: BMW Страницы: 416

California EV V1100

Бренд: MOTO GUZZI Страницы: 173

Бренд: Yamaha Страницы: 338

Бренд: ACERBIS Страницы: 72

Бренд: HYOSUNG Страницы: 74

Бренд: VOIGT MT Страницы: 2

Бренд: Yamaha Страницы: 66

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 120

Бренд: Denali Страницы: 2

Бренд: RS Motorcycle Solutions Страницы: 2

Бренд: KEDO Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды