manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Руководство пользователя, Страница: 39 / 148

Поделиться
Скачать
APRILIA RSV 1000 R FACTORY Скачать руководство пользователя страница 39

39

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

DIAGNOSTICS

1) Each time the ignition key is in the "

"

position, the wording "

efi

" is displayed

for about three seconds.

CAUTION

When the "

efi

" wording turns on and

the warning light (

) comes on during

normal engine operation, it means that
the Engine Control Unit has detected an
anomaly. 
In most cases the engine will keep
r u n n i n g ,   b u t   w i t h   l e s s   t h a n   i d e a l
performance. However, contact an

aprilia 

Official dealer without delay. 

ENGINE OIL PRESSURE

Each time the ignition key is in the "

"

position, the engine oil pressure logo
comes on for about three seconds.

CAUTION

If the engine oil pressure logo stays on
and the warning light (

) comes on as

well, after engine firing or during normal
engine operation, it means that the
engine oil pressure is low.
S t o p   t h e   e n g i n e   i m m e d i a t e l y   a n d
contact an 

aprilia 

Official dealer.

SETTING THE RED LINE THRESHOLD 
(WITH ENGINE OFF ONLY)

W h e n   t h e   m a x i m u m   r p m   s e t   i s
exceeded, the red line warning light
( r e d )   ( 1 )   o n   t h e   d a s h b o a r d   s t a r t s
blinking.

NOTE 

The red line threshold, which

operates the red line light, can only be set
with the engine off and the odometer
displayed. The setting range is 2,000 -
12,000 rpm.

The factory setting is 6,000 rpm.

To view the red line threshold setting, hold
down the "Trip/V" button for at least 3
seconds. The rev counter pointer (2) will
point to the corresponding rpm for three
seconds.

1

2

APRum_RSV1000R##06_####.book  Page 39  Monday, February 6, 2006  2:48 PM

Содержание RSV 1000 R FACTORY





















































































































































Отзывы:

Нет отзывов