APRILIA RSV 1000 R FACTORY Скачать руководство пользователя

Страница: 36 / 148

use and maintenance

RSV 1000 R

- RSV 1000 RFACT

USA

ODOMETER AND TRIP METER
DISPLAY (TRIP 1 AND TRIP 2)

Turn the ignition key to "



", to display the

odometer. To switch to the trip meter
(km/mi) (TRIP 1 and TRIP 2), press the
Trip/V button.

To reset TRIP 1, select Trip 1 display and
hold down the "Trip/V" button for at least 3
seconds.

To reset TRIP 2, select Trip 2 display and
hold down the "Trip/V" button for at least 3
seconds.

NOTE

The trip meter indications reflect

the distance covered since last resetting.

Trip 1 and Trip 2 indications are wiped
off when the battery is disconnected.

↓

TRIP/V

ODOMETRO

↓

TRIP/V

TRIP 1

↓

TRIP/V

TRIP 2

↓

TRIP/V

APRum_RSV1000R##06_####.book Page 36 Monday, February 6, 2006 2:48 PM

Содержание RSV 1000 R FACTORY





















































































































































Результаты поиска

Содержание RSV 1000 R FACTORY

Отзывы:

Похожие инструкции для RSV 1000 R FACTORY

Бренды по названию

Популярные бренды

APRILIA RSV 1000 R FACTORY, Руководство пользователя

Результаты поиска

Содержание RSV 1000 R FACTORY

Отзывы:

Похожие инструкции для RSV 1000 R FACTORY

Бренды по названию

Популярные бренды