background image

Instruction Rev04

0

mm

10

20

30

40

50

60

70

80

90

Thank you for choosing DENALI

We know you would rather be riding your bike than wrenching on it, so we go the extra 

mile to make sure our instructions are clear and as easy to understand as possible. If 

you have any questions, comments, or suggestions don’t hesitate to give our gear 

experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM

Please Read Before Installing 

DENALI products should always be installed by a qualified motorcycle technician. If 

you are unsure of your ability to properly install a product, please have the product 

installed by your local motorcycle dealer. DENALI takes no responsibility for damages 

caused by improper installation. 

Caution:

 When installing electronics it is extremely 

important to pay close attention to how wires are routed, especially when mounting 

products to the front fender, front forks, or fairing of your motorcycle. Always be sure 

to turn the handlebars fully left, fully right, and fully compress the suspension to 

ensure the wires will not bind and have enough slack for your motorcycle to operate 

properly.

 

   

Installation Tips

We strongly recommend using medium strength liquid thread locker on all screws, 

nuts, and bolts. It is also important to ensure that all hardware is tightened to the 

proper torque specifications as listed in your owner’s manual. For included accessory 

hardware please refer to the default torque specifications provided below. Inspect all 

hardware after the first 30 miles to ensure proper torque specifications are 

maintained.  

Hardware Sizing Guide

Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc. 

Remember, the length of a screw or bolt is measured from the start of the “mounting 

surface” to the end of the screw, so only include the screw head when measuring 

countersunk screws.  

M3

10.0 in-lbs

-

1.0 Nm

M4

23.0 in-lbs

-

2.5 Nm

M5

44.5 in-lbs

3.5 ft-lbs

5.0 Nm

M6

78.0 in-lbs

6.5 ft-lbs

9.0 Nm

M8

-

13.5 ft-lbs

18.0 Nm

M10

-

30.0 ft-lbs

41.0 Nm

M12

-

52.0 ft-lbs

71.0 Nm

in-lbs

ft-lbs

Nm

Bolt Size

0

in

1

2

3

What’s In The Box?

DENALIELECTRONICS.COM

HMT.07.11000

BMW R1250GS

Split Horn Mounting Bracket

Instruction Manual

(a) Acoustic Horn Bracket......(HMT.07.014)................................Qty 1
(b) Compressor Bracket......(HMT.07.013)....................................Qty 1
(c) M8x75mm - SocketHead Screw............................................Qty 2
(d) M8 Washer.........................................................................Qty 2
(e) M8 Spacer...OD 19.05mm, ID 8.1mm, L 19.05mm...................Qty 2
(f) M6 Spacer...OD 9.53mm, ID 6.53mm, L 7.938mm...................Qty 1

(g) M6 Washer..........................................................................Qty 2
(h) M6x25mm - Lens Head Screw................................................Qty 2
(i) M8 Nut Cap.........................................................................Qty 1

Kit Contents

Tools Required:

 13mm Wrench, 10mm Wrench, 6mm Allen Key, 4mm 

Allen Key, T30 Torx Bit for factory screw removal.

(a)

(b)

(c)

(h)

(f)

(g)

(i)

(e)

(d)

Reviews: