manualshive.com logo in svg

Amphenol Temposonics GB SSI Series, Руководство по эксплуатации, Страница: 23 / 25

Поделиться
Скачать
Amphenol Temposonics GB SSI Series Скачать руководство пользователя страница 23

23

Temposonics

®  

GB-Series SSI

Operation Manual

8/ 

With position magnet # 251 416-2

9/ 

For option 

H

 ( −40…+100 °C / −40…+212 °F) an aluminum cover plate is used

8.2 Technical data GB-M / GB-T

Output

Interface

SSI (Synchronous Serial Interface) – Differential signal in SSI standard

Data format

Binary, gray

Programming

Programming of set points using optional accessories

Measured value

Position

Measurement parameters

Resolution

5 µm minimum

Cycle time

Up to 3.7 kHz depending on stroke length

Linearity 

8

≤ ±0.02 % F.S. (minimum ±60 µm) typical

Repeatability

≤ ±0.005 % F.S. (minimum ±20 µm) typical 

Operating conditions

Operating temperature

−40…+90 °C (−40…+194 °F), option: −40…+100 °C (−40…+212 °F)

Ingress protection

IP67 (if mating connectors are correctly fitted)
IP68 (for cable outlet)

Shock test

100 g (single shock) IEC standard 60068-2-27

Vibration test

15 g / 10…2000 Hz IEC standard 60068-2-6 (excluding resonant frequencies)

EMC test

Electromagnetic emission according to EN 61000-6-4
Electromagnetic immunity according to EN 61000-6-2
The sensor meets the requirements of the EU directives and is marked with 

Operating pressure

350 bar (5076 psi), 700 bar (10,153 psi) peak (at 10 × 1 min)

Magnet movement velocity

Any

Design / Material

Sensor electronics housing 

9

 with flange

Stainless steel 1.4305 (AISI 303)

Sensor rod

Stainless steel 1.4306 / 1.4307 (AISI 304L)

Stroke length

25…3250 mm (1…128 in.)

Mechanical mounting 

Mounting position

Any

Mounting instruction

Please consult the technical drawings on page 10

Electrical connection

Connection type

M12 A-coded male connector (8 pin); M16 male connector (7 pin); Cable outlet

Operating voltage

+24 VDC (−15 / +20 %)

Ripple

≤ 0.28 V

PP

Current consumption

90 mA typical

Dielectric strength

500 VDC (DC ground to machine ground)

Polarity protection

Up to −30 VDC

Overvoltage protection

Up to 36 VDC

Содержание Temposonics GB SSI Series


























Отзывы:

Нет отзывов