Amphenol Temposonics GB SSI Series Скачать руководство пользователя страница 10

Страница: 10 / 25

Temposonics

GB-Series SSI

Operation Manual

M12 connector (Example: With flat-faced flange)

Threaded flange »M«:

M18×1.5-6g

55
(2.17)

M4 (3×)

77.4 (3.05)

(Ø 2.13)

54.5 (2.15)

22.9 (0.9)

(1)

4.1

(0.16)

(0.55)

Null zone

(1.57)

Stroke length

25…3250

(1…128)

Dead zone

63.5

(2.5)

0.13

(Ø

0.39

0.01)

0.13

(Ø

0.39

0.01)

0.13

(Ø

0.39

0.01)

67.5 (2.66)

(Ø 2.13)

54.5 (2.15)

(0.51)

4.1

(0.16)

(0.55)

Null zone

(1.57)

Dead zone

63.5

(2.5)

66 (2.6)

52.5 (2.07)

13.5 (0.53)

(0.55)

Null zone

(1.57)

Sensor electronics

housing

(1.54)

M12 connector

Threaded flange »M«:

M18×1.5-6g

M4 (3×)

55
(2.17)

(1)

Stroke length

25…3250

(1…128)

(1)

Sensor electronics

housing

(1.54)

Sensor electronics

housing

(1.54)

M16 connector

Threaded flange »T«:

¾"-16 UNF-3A

(Ø

2.13)

M4 (3×)

55
(2.17)

Stroke length

25…3250

(1…128)

Dead zone

63.5

(2.5)

Magnet

2.5

(0.1)

Ø 25.4

(Ø 1)

A/F 55

M16 connector (Example: With raised-faced flange)

Threaded flange »M«:

M18×1.5-6g

55
(2.17)

M4 (3×)

77.4 (3.05)

(Ø 2.13)

54.5 (2.15)

22.9 (0.9)

(1)

4.1

(0.16)

(0.55)

Null zone

(1.57)

Stroke length

25…3250

(1…128)

Dead zone

63.5

(2.5)

0.13

(Ø

0.39

0.01)

0.13

(Ø

0.39

0.01)

0.13

(Ø

0.39

0.01)

67.5 (2.66)

(Ø 2.13)

54.5 (2.15)

(0.51)

4.1

(0.16)

(0.55)

Null zone

(1.57)

Dead zone

63.5

(2.5)

66 (2.6)

52.5 (2.07)

13.5 (0.53)

(0.55)

Null zone

(1.57)

Sensor electronics

housing

(1.54)

M12 connector

Threaded flange »M«:

M18×1.5-6g

M4 (3×)

55
(2.17)

(1)

Stroke length

25…3250

(1…128)

(1)

Sensor electronics

housing

(1.54)

Sensor electronics

housing

(1.54)

M16 connector

Threaded flange »T«:

¾"-16 UNF-3A

(Ø

2.13)

M4 (3×)

55
(2.17)

Stroke length

25…3250

(1…128)

Dead zone

63.5

(2.5)

Magnet

2.5

(0.1)

Ø 25.4

(Ø 1)

A/F 55

Cable outlet (Example: With flat-faced flange)

Threaded flange »M«:

M18×1.5-6g

55
(2.17)

M4 (3×)

77.4 (3.05)

(Ø 2.13)

54.5 (2.15)

22.9 (0.9)

(1)

4.1

(0.16)

(0.55)

Null zone

(1.57)

Stroke length

25…3250

(1…128)

Dead zone

63.5

(2.5)

0.13

(Ø

0.39

0.01)

0.13

(Ø

0.39

0.01)

0.13

(Ø

0.39

0.01)

67.5 (2.66)

(Ø 2.13)

54.5 (2.15)

(0.51)

4.1

(0.16)

(0.55)

Null zone

(1.57)

Dead zone

63.5

(2.5)

66 (2.6)

52.5 (2.07)

13.5 (0.53)

(0.55)

Null zone

(1.57)

Sensor electronics

housing

(1.54)

M12 connector

Threaded flange »M«:

M18×1.5-6g

M4 (3×)

55
(2.17)

(1)

Stroke length

25…3250

(1…128)

(1)

Sensor electronics

housing

(1.54)

Sensor electronics

housing

(1.54)

M16 connector

Threaded flange »T«:

¾"-16 UNF-3A

(Ø

2.13)

M4 (3×)

55
(2.17)

Stroke length

25…3250

(1…128)

Dead zone

63.5

(2.5)

Magnet

2.5

(0.1)

Ø 25.4

(Ø 1)

A/F 55

Controlling design dimensions are in millimeters and measurements in ( ) are in inches
Unless otherwise stated, apply to the general tolerances according to DIN ISO 2768-m

4.3 Styles and installation of Temposonics

GB-M / GB-T / GB-B

(rod sensor with threaded flange)

Fig. 7: Temposonics

GB-M / GB-T

Содержание Temposonics GB SSI Series


























Результаты поиска

Содержание Temposonics GB SSI Series

Отзывы:

Amphenol Temposonics GB SSI Series, Руководство по эксплуатации, Страница: 10 / 25

Результаты поиска

Содержание Temposonics GB SSI Series

Отзывы: