Ampac ZoneSense DH4 Скачать руководство пользователя

Страница: 6 / 35

Page 2

ZONESENSE DH4

OPERATORS MANUAL

System

Overview

The

ZoneSense DH4

Fire Alarm Control Panel (FACP) is supplied, as a four (4) Zone Conventional

FACP with two (2) dedicated Alarms and Door Holder outputs. It can be supplied in either ABS (BX1)
or Metal cabinet (BX10)

Features include:



Controls that have tactile and audible feedback of operation.



On-site

programming.



Terminals cater for up to 2.5mm diameter cables.

Buzzer Operation



The buzzer provides audible:



Indication at system start-up (3 tone bursts of increasing frequency)



Indication of a fire condition. Tone is continuous, until the buzzer is silenced or the fire

condition is cleared by reset.



Indication of a fault condition. Tone is 1 second on, 1 second off, until the fault condition

clears.



Feedback when a key is pressed.



Feedback when multiple keys are pressed simultaneously or illegal key press (for example

RESET when at access level 1) or there is a timeout condition entering the password.

The buzzer



Is silenced by SILENCE BUZZER but will resound on any new alarm or fault condition.



Sounds during a lamp test.



Sounds (fault indication), when the power supply is not calibrated.



Sounds when calibration is successful (same tone bursts as at system start-up)

Содержание ZoneSense DH4




































Результаты поиска

Содержание ZoneSense DH4

Отзывы:

Похожие инструкции для ZoneSense DH4

Бренды по названию

Популярные бренды

Ampac ZoneSense DH4, Установка, наладка и эксплуатация

Результаты поиска

Содержание ZoneSense DH4

Отзывы:

Похожие инструкции для ZoneSense DH4

Бренды по названию

Популярные бренды