manualshive.com logo in svg

Ampac ZoneSense DH4, Установка, наладка и эксплуатация

Поделиться
Скачать
Ampac ZoneSense DH4 Скачать руководство пользователя страница 22

 

Page 18 

ZONESENSE DH4

 

OPERATORS MANUAL

Operation of the silence/resound control has no effect on the door holder 
output state 

Activating the reset switch, will cancel the evacuate condition, which results in the alarm outputs 
being turned off, door holder outputs activated and the common fire led being extinguished.  

 Next 

 - Active at access level 1 and 2. 

At access level 1, the Next 

 key is used to enter the 0 digit of the 3210 password. 

At access level 2, the Next 

 key is used to select zone circuits for the walk test and outputs for 

disable / re-enable. 

 Lamp Test 

 - Active at access level 1 and 2. 

At access level 1, the Lamp Test 

 key is used to enter the 1 digit of the 3210 password, and 

instigate a lamp and buzzer test if the key is depressed for 3 seconds or more. The lamp test 
sequentially illuminates all indicators and sounds the buzzer for approximately 1 second.  

Note:

 

The lamp test will be cancelled if a fire condition is to be announced and can not be 

instigated if a fire condition is present. 

Note:

 

The lamp test is cancelled if a fault condition is to be announced but can be instigated if a 

fault condition is present. 

At access level 2, the Lamp Test 

 key is used to commence the walk test. 

 Disable/Enable 

 

Active at access level 1 and 2 

At access level 1, is used to enter the 2 digit of the 3210 password. 

At access level 2, is used to disable / enable selected zones and / or outputs. 

 Exit 

 

Active at access level 1 and 2. 

At access level 1, Exit 

 is used to enter the 3 digit of the 3210 password. 

At access level 2, Exit 

 is used to exit from the disable / enable, and walk test procedure. 

Содержание ZoneSense DH4




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды