Ampac ZoneSense DH4 страница 24 Скачать руководство пользователя | Manualshive

Страница: 24 / 35

background image

Page 20

ZONESENSE DH4

OPERATORS MANUAL

Test - Amber

Illuminated to show that the FACP is in the Walk Test mode. The indicator is illuminated steady
when the walk test is active.

Fire Output On - Red

Illuminates steady when the “Fire Output” relay is active as a result of a fire condition.

6.3.2 Control

Indicators

There are five (5) control indicators within the central control area of the FACP.

Common Fire - Red

Common fire indicator will be flashing at the alarm rate when a fire condition is present or the
evacuate control is operated (when the FACP is at access level 2). The indicator will become steady
when silence resound switch is pressed.

A new fire condition or activation of the evacuate control will cause the indicator to flash again.

Common Fault - Amber

Fault indicator - illuminated steady by any fault condition.

Disabled - Amber

Disabled indicator illuminated steady by any disablement on any zone or output.

Door Released - Amber

The indicator is illuminated when the door holder outputs (1 & 2) have been deactivated.

Alarms Status - Amber

This indicator is immediately above the Alarms silence / resound switch and indicates a disable
condition (steady) or a fault condition (flashing at the fault rate) on any of the alarm outputs.

Display priority: Disable (steady) then fault (flash)

«
...
22
23
24
25
26
...
»

Содержание ZoneSense DH4




































Отзывы:

Нет отзывов

Похожие инструкции для ZoneSense DH4

Бренд: Kentec Electronics Страницы: 18

Бренд: Vigilant Страницы: 36

Бренд: Zeta Страницы: 27

Бренд: Kentec Electronics Страницы: 107

Бренд: Fire-Lite Alarms Страницы: 2

Бренд: Wheelock Страницы: 4

Бренд: Jade Bird Страницы: 4

Бренд: Ziton Страницы: 113

Бренд: Bosch Страницы: 31

Бренд: Panasonic Страницы: 142

Бренд: Maxfire Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды