Ampac ZoneSense DH4 Скачать руководство пользователя | Manualshive

Страница: 25 / 35

background image

Page 21

ZONESENSE DH4

OPERATORS MANUAL

6.3.3 Zone

Indicators

There are two indicators for each alarm zone fitted to the FACP.

Zone Fire – Red

Individual zone Indicators showing when each zone is in the fire condition (flashing at the alarm rate)
and will become steady when silence resound switch is pressed. An incoming alarm on another zone
will cause that fire indicator to flash while the original indicator will remain steady.

Zone Fault / Disabled / Test – Amber

Flashes at the fault rate due to a fault condition on individual zones. Disabling that zone causes the
LED to become steady. Reminder - the disablement has priority over displaying a fault condition.

Other Indications

The zone indicators are utilised in the disable /enable and walk test process. The following table
summarises the functionality of the zone indicators:

Condition Fire

Indicator

Fault/Disabled Test Indicator

Alarm (un-silenced)

Flashing at the alarm rate

-

Alarm (silenced)

Steady

-

Fault

-

Flashing at the fault rate

Disabled

-

Steady (priority over fault)

Normal -

-

Disable / Enable Operation

Disable -

Rapid

Flash

Enable

Slow

Flash

Walk Test

Selected and under
test

Steady – when the alarm condition
has been detected (3 seconds only)

Rapid Flash

«
...
23
24
25
26
27
...
»

Содержание ZoneSense DH4




































Отзывы:

Нет отзывов

Похожие инструкции для ZoneSense DH4

Бренд: LST Страницы: 1

Бренд: Fike Страницы: 28

Бренд: Mackie Страницы: 1

Kidde AirSense SynaG Series

Бренд: UTC Fire and Security Страницы: 104

Бренд: Radionics Страницы: 29

Бренд: Satel Страницы: 8

Бренд: Horing LIH Страницы: 24

Бренд: Global Fire Equipment Страницы: 2

Бренд: Global Fire Equipment Страницы: 2

MPX-SNDR-DG - 4 V2

Бренд: Global Fire Equipment Страницы: 2

Бренд: Global Fire Equipment Страницы: 2

ORION EX MINI-REP

Бренд: Global Fire Equipment Страницы: 11

Бренд: Fire Sense Страницы: 33

Бренд: Ampac Страницы: 2

Warning Sign 4210-011

Бренд: Ampac Страницы: 3

FireFinder NZS 4512

Бренд: Ampac Страницы: 2

Apartment Module

Бренд: Ampac Страницы: 4

FireFinder NZS 4512

Бренд: Ampac Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды