Ampac ZoneSense DH4 страница 29 Скачать руководство пользователя

Страница: 29 / 35

Page 25

ZONESENSE DH4

OPERATORS MANUAL

7.4.1 Example of Disabling the Fault Output

Step 1:

Enter the level 2 password by pressing these

keys in the following order.

The

LED will illuminate (steady)

Step 2:

Press

and the Zone 1 FAULT/DISABLE/TEST LED will flash and

will

flash. (slow for enabled, fast for disabled).

Step 3:

Press

to step through the options until

LED is illuminated

(slow for enabled, fast for disabled)) and press

again. The Fault Output Disabled LED

will continue flashing while the disablement is being established and then become steady once the

disablement is established as will the

LED.



Note:

Disablement and re-enablement of any of the above is not affected by Reset from the fire

alarm condition or the fault condition and can only be carried out by following the appropriate
procedure at access level 2.



Note:

Disable has priority over the fault condition. Disabling a zone will override the alarm

condition and cause any outputs activated as a result of the zone going into alarm to be cleared.

Содержание ZoneSense DH4




































Результаты поиска

Содержание ZoneSense DH4

Отзывы:

Похожие инструкции для ZoneSense DH4

Бренды по названию

Популярные бренды

Ampac ZoneSense DH4, Установка, наладка и эксплуатация

Результаты поиска

Содержание ZoneSense DH4

Отзывы:

Похожие инструкции для ZoneSense DH4

Бренды по названию

Популярные бренды