manualshive.com logo in svg

Ampac ZoneSense DH4, Установка, наладка и эксплуатация

Поделиться
Скачать
Ampac ZoneSense DH4 Скачать руководство пользователя страница 10

 

Page 6 

ZONESENSE DH4

 

OPERATORS MANUAL

4.7 

Power Supplies and AC Mains Installation 

4.7.1  Primary Power Supply 

The FACP consists of the Main Control Card and mains transformer. The control board is broken 
into two sections, the main control circuitry and the power supply / charger. 

4.7.2 Mains 

wiring 

The requirement for the Mains supply to the FACP is fixed wiring, using three core cable (no less 
than 0.75mm

²

 and no more than 2.5mm

²

) or a suitable three conductor system, fed from an isolating 

switch fuse spur, fused at 3A. This should be secured from unauthorised operation and be marked 
'FIRE ALARM: DO NOT SWITCH OFF. The Mains supply must be exclusive to the FACP.  

4.7.3  Connecting the Panel 

Connecting 

ZoneSense – DH4

 internal connections and boards is best undertaken immediately prior 

to Commissioning. 

Before beginning ensure all devices on the circuits are correctly connected and that cable integrity is 
verified throughout the installation.  

 

Important: DO NOT use an insulation tester ('Megger') with any electronic devices connected. 

Faults occurring in the wiring which are not picked up at this stage will almost certainly result in 
spurious and intermittent faults when the equipment is energised. 

 

Important: Under no circumstances should the 

ZoneSense PLUS - AR

 panel be operated 

without the Power Supply correctly mounted in the enclosure and the retaining screws securely 
tightened.  

4.7.4  Connecting the Mains Earth 

All earth cabling shall be terminated to the panel Chassis Earth Terminal in a star configuration. 

The earth cable closest to the cabinet body shall have an M4 SPW beneath the lug then an M4 SPW 
and M4 nut. 

Each additional earth cable shall be terminated with an M4 SPW and M4 nut. 

An additional M4 nut and M4 SPW are fitted to the Chassis Earth Terminal for installers to connect 
their Mains Earth. 

M4 Shake Proof Washer

M4 Shake Proof Washer

CHASSIS EARTH TERMINAL

M4 Nut

Earth Cable

Earth Cable

M4 Nut

M4 Shake Proof Washer *

M4 Nut *

Note:

* Extra M4 Nut and M4 SPW are

  provided finger tight on the Earth bolt.

 

Figure 3: Panel Earthing 

4.7.5  Connecting the Mains Power to the Mains Transformer 

CAB2875

TO  EARTH

OUTPUT OF

TERMINAL

FUSE

BLOCK

MAINS

TRANS-

FORMER

NEUTRAL           EARTH         LIVE

FUSE = 0.5A

M205

 

Figure 4: Mains Transformer Wiring 

Содержание ZoneSense DH4




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды