AML AML M71V2 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 130

background image

106

The purpose of the laser aim is to be able to tell where the laser
beam is pointing when scanning bar codes that are a long way
away from the unit. The laser point helps to locate the beam before
the laser starts rastering. Once the laser starts rastering, the bar
code will be scanned.

Laser Timeout

Turns off Laser / CCD after (1 – 9) seconds when the trigger is
pushed in Pulse mode, or held down in Trigger mode. The laser /
CCD will always turn off immediately after a good read.

Read Verify

Performs bar code re-reads the number of times (0 – 9) required for
applications where accuracy is critical. This is used where the bar
code is poorly printed or damaged.

Imager Options (2D Imager Only)

These options are used to configure the 2D Imager device behavior, and the trigger mode
for the M71V2 handheld terminal.

Trigger Mode

Trigger

Trigger activates scanning device for as long as trigger is held up
to the Laser Timeout value in seconds. (Recommended)

Pulse

Continues to keep the scanner active even when the trigger is not
held down, up to Laser Timeout value in seconds.

Laser Timeout

Turns off Laser / CCD after (1 – 9) seconds when the trigger is
pushed in Pulse mode, or held down in Trigger mode. The laser /
CCD will always turn off immediately after a good read.

Aim Time (mS)

The amount of time the green LED aiming beam is on.

The purpose of the LED aiming beam is to be able to locate where
the center of the LED beam is pointing when scanning bar codes

«
...
108
109
110
111
112
...
»

Содержание AML M71V2



































































































































Отзывы:

Нет отзывов

Похожие инструкции для AML M71V2

Бренд: TEC Страницы: 24

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 8

Бренд: NI Страницы: 11

Бренд: Vectron Страницы: 112

Бренд: NCR Страницы: 90

Бренд: Feig Electronic Страницы: 40

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 6

Бренд: Siemens Страницы: 8

NT2S-SF121B-E -

Бренд: Omron Страницы: 31

Бренд: Burnside Страницы: 2

Camera Station S9101 Mk II

Бренд: Axis Страницы: 27

Бренд: Custom Audio Electronics Страницы: 16

Бренд: Custom Audio Electronics Страницы: 16

Бренд: ACP Страницы: 24

Бренд: POSIFLEX Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды