AML AML M71V2 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 130

background image

16

GSM/GPRS Network Card Support

The AML M71V2 now supports GSM/GPRS network cards.

When a GPRS network card

comes installed in the M71V2, the menus will be slightly different from the standard menus.

To determine if the unit has the correct firmware installed. Use the M71V2 Menu System and
select “Diagnostic Menu > Firmware Versions” and see under RAM DISK IMAGE the version

1.3.0-32

firmware.

Installing the GPRS SIM Card

The M71V2 GSM/GPRS card requires a customer supplied SIM (Subscriber Identity Module)
card issued by the cellular network Access Provider (e.g. T-Mobile, Cingular or Verizon). This
card must be installed prior to using the M71V2 GSM/GPRS system.

1. Remove the 2 screws

holding on RF end cap.

2. Pull RF cap down

slightly, and then out

from body of terminal.

3. Carefully pull GSM/GPRS card

straight out of terminal. Note the

orientation of card when replacing it

back into unit.

5. Note the location of the

beveled corner on SIM card

with metal contacts pointing

out.

6. Close SIM cover and

push down to lock SIM

card into place.

4. Push metal door up to release

then rotate the SIM door open.

«
...
18
19
20
21
22
...
»

Содержание AML M71V2



































































































































Отзывы:

Нет отзывов

Похожие инструкции для AML M71V2

Бренд: Union Community Страницы: 28

Бренд: amber connect Страницы: 11

Бренд: Quest Payment Systems Страницы: 37

Бренд: Omnicomm Страницы: 58

Бренд: Sharp Страницы: 2

Бренд: Sharp Страницы: 8

Бренд: Sharp Страницы: 16

Бренд: Sharp Страницы: 21

Бренд: Sharp Страницы: 32

Бренд: Sharp Страницы: 295

Camera Station S9101 Mk II

Бренд: Axis Страницы: 27

Бренд: Crestron Страницы: 4

Бренд: Hisense Страницы: 41

Бренд: Stahl Страницы: 25

Бренд: 3nStar Страницы: 23

VIPA TP-ECO TP 607LC

Бренд: YASKAWA Страницы: 75

Бренд: FALCOM Страницы: 15

HUGHES BGAN Patrol

Бренд: EchoStar Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды