AMI 186 Скачать руководство пользователя страница 44

Страница: 44 / 65

IEEE-488 Communication Option

IEEE-488 Command Set Reference

and then reapplied to the instrument. If the configuration is changed from the front
panel, the settings are automatically saved to permanent memory.

Commands for querying the configuration

The HI, LO, A, B, INTERVAL, and LENGTH commands return the current
configuration of the instrument. Each return value is terminated with

<LF>

and EOI.

Command for returning a level measurement

The LEVEL command returns the liquid level in the current units selected through the
communication interface.

Command:

Function:

Returns the HI
setpoint limit in the
current units

Returns:

<value>

Command:

Function:

Returns the LO
setpoint limit in the
current units

Returns:

<value>

Command:

Function:

Returns the A
setpoint limit in the
current units

Returns:

<value>

Command:

Function:

Returns theB
setpoint limit in the
current units

Returns:

<value>

Command:

INTERVAL

Function:

Returns the fill timer
setting in minutes

Returns:

<value>

Command:

LENGTH

Function:

Returns the sensor
length in the current
units

Returns:

<value>

Command:

LEVEL

Function:

Returns the liquid
level in the current
units

Returns:

<value>

Содержание 186


































































Результаты поиска

Содержание 186

Отзывы:

Похожие инструкции для 186

Бренды по названию

Популярные бренды

AMI 186, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 186

Отзывы:

Похожие инструкции для 186

Бренды по названию

Популярные бренды